Kyocera KM-3050

2GN/2GP/2GR
1-4-8
Optional
finisher
83
Exit sensor stay jam
(3000-sheet document finisher)
Eject switch 1 (ESW1) is not turned off within specified
time of its turning on.
1182 ms
(Document finisher)
In the straight mode, the exit sensor (EXS) is not turned
off within specified time of its turning on.
1680 ms
(Document finisher)
In the offset or staple mode, the exit sensor (EXS) is not
turned off within specified time of its turning on.
5375 ms
(Built-in finisher)
The paper conveying switch (PCSW) does not turn off
within specified time of its turning on when paper is
ejected to the finisher tray from the intermediate tray.
Paper length +
1123 ms (30 ppm)
Paper length +
869 ms (40/50 ppm)
84
Jam in eject section of
right sub tray (3000-
sheet document fin-
isher only)
Eject switch 2 (ESW2) is not turned off even if a specified
time has elapsed after the machine eject signal was
received.
1562 ms (30 ppm)/
1209 ms (40/50 ppm)
Eject switch 2 (ESW2) is not turned on even if a specified
time has elapsed after the machine eject signal was
received.
1562 ms (30 ppm)/
1209 ms (40/50 ppm)
Eject switch 2 (ESW2) is not turned off within specified
time of its turning on.
2989 ms (30 ppm)/
2313 ms (40/50 ppm)
85
Jam in eject section of
left sub tray (3000-
sheet document fin-
isher only)
Eject switch 3 (ESW3) does not turn off within specified
time of paper entry sensor (PES) turning on.
1843 ms (30 ppm)/
1426 ms (40/50 ppm)
Eject switch 3 (ESW3) does not turn on within specified
time of paper entry sensor (PES) turning on.
1843 ms (30 ppm)/
1426 ms (40/50 ppm)
Eject switch 3 (ESW3) is not turned off within specified
time of its turning on.
2989 ms (30 ppm)/
2313 ms (40/50 ppm)
86
Jam in eject section of
internal tray 1 (3000-
sheet document fin-
isher only)
Internal tray entry sensor 1 (ITPES1) is not turned on
even if a specified time has elapsed after the eject signal
was received.
2674 ms (30 ppm)/
2070 ms (40/50 ppm)
87
Jam in eject section of
internal tray 2 (3000-
sheet document fin-
isher only)
Internal tray entry sensor 2 (ITPES2) does not turn on
within specified time of internal tray entry sensor 1
(ITPES1) turning on.
1708 ms (30 ppm)/
1322 ms (40/50 ppm)
Internal tray entry sensor 2 (ITPES2) does not turn off
within specified time of internal tray entry sensor 1
(ITPES1) turning off.
676 ms
88
Jam in eject section of
main tray (3000-sheet
document finisher only)
Eject switch 1 (ESW1) is not turned on within specified
time.
1324 ms
Side registration home position sensor 1 (SRHPS1) is not
turned off within specified time of its turning on.
500 ms
Side registration home position sensor 2 (SRHPS2) is not
turned off within specified time of its turning on.
500 ms
The paper conveying belt detection sensor (PCBDS) is
not turned off within specified time.
2000 ms
Section Description Conditions Specified time