11. Appendix MX-FR Series Modular Matrix Frames – User's Manual 183
▪
used to deembed audio. Fixed on MX-HDMI-3D-IB-S, MX-HDMI-3D-OB-S, MX-HDMI-OB, MX-TPS-IB-S,
MX-TPS-OB-S.
▪
packets were still present), the MX-HDMI-OB, MX-DVI-HDCP-OB and preview output have sent a 53Khz
invalid SPDIF signal. This caused a clicking noise with some AV receiver.
▪
audio). Affected cards: MX-HDMI-3D-IB, MX-HDMI-3D-OB, MX-TPS-IB, MX-TPS-OB
3.3.8
Released: 2013-10-01
▪
commands are only valid for the 80x80 frame.
▪ If input signal was present on a SII9575 port and test pattern mode was changed from "Off" to "No
signal mode", SII9575 output had been turned off for a short period unnecessarily. Fixed. Affected
cards: MX-HDMI-3D-IB, MX-HDMI-3D-OB, MX-TPS-IB, MX-TPS-OB.
▪
Affected cards: MX-HDMI-OB, MX-TPS-OB-S, MX-TPS-OB-A, MX-HDMI-3D-OB-S, MX-HDMI-3D-OB-A.
▪ Firmware v3.3.7 sometimes rebooted with 2 or 4 line LCD display.
▪ The cycle testpattern has stopped sometimes for a few minutes.
▪ If an error happened during the booting process, there was no alert displayed on the LCD screen
(however the event has been logged).
▪ If the errorlog menu was active on the 4-line LCD screen, then a new incoming alert may confuse the
lines on the LCD screen.
▪ Lightware simple protocol mode (P_3) could hang if an unknown command had been received.
▪
▪ Error log downloading over USB was bugous.
3.3.9
Released: 2013-10-22
▪ Display Range Limits Descriptor was not correct in factory EDIDs (except universal EDIDs).
3.4.0
Released: 2014-01-13
New feature
▪ MX-HDMI-OPT-OB-R support has been added.
▪ New factory EDIDs have been added: 3D compliant, 4K, 4K universal EDIDs and most often used pc
graphics resolutions with audio support.
▪
▪ If one or more MX-TPS-IB or MX-TPS-OB (including audio addon versions) were installed in the frame,
▪
strange resolution or could not detect the incoming signal, if the DVII input changed from no sync
screen to incoming signal. Fixed.
▪ Green sparks could appear in the output signal of MX-HDMI-3D-OB, if the input signal was coming from
MX-HDMI-3D-IB and was switched between 1080p and 480p by the crosspoint.
3.4.1
Released: 2014-03-31
▪ Some monitors that do not terminate the TMDS lines in standby mode, could not wake up from this
state, when input signal was connected through MX-HDMI-3D-OB or MX-TPS-OB. This issue is now
hotplug event. Affected cards: MX-HDMI-3D-OB, MX-TPS-OB.
▪ 4line LCD - View EDID menu froze the LCD task if there were no IO cards in the matrix.
▪ 4line LCD - FR80 - View EDID did not show the 81st input and output.
▪ 4line LCD - View EDID - Dynamic EDIDs was not displayed if there were no input cards in the same
numbered slot (the problem was checking the input cards instead of the output cards)
▪ Too long lines in the error log may have disrupted the log reading if special charachters were used.
▪ The text of the test pattern generator clock menu on the LCD screen was disambigous.
▪
▪
3.4.2
Released: 2014-05-26
New feature
▪
3.4.3
Released: 2014-06-27
▪ A rare ADM1063 false alarm has appeared on the LCD or sometimes the internal voltages were reported
improperly. Affected frame: MX-FR80
To Next Page
Loading...
Need help?
General
