Mitsubishi Electric MELSEC iQ-F Series - Page 240

238
10 TROUBLESHOOTING
10.5 List of Error Codes
D615H Parameter error (each station device range
assignment error (RY))
• Write the network parameter to the CPU module again.
• Execute again after correcting the size of the device station link
device in the setting data.
• If the error occurs again even after taking the above, please
consult your local Mitsubishi representative.

D616H Parameter error (each station device range
assignment error (RY))
• Write the network parameter to the CPU module again.
• Execute again after correcting the offset of the device station link
device in the setting data.
• If the error occurs again even after taking the above, please
consult your local Mitsubishi representative.

D617H Parameter error (each station device range
assignment error (RX))
• Write the network parameter to the CPU module again.
• Execute again after correcting the size of the device station link
device in the setting data.
• If the error occurs again even after taking the above, please
consult your local Mitsubishi representative.

D618H Parameter error (each station device range
assignment error (RX))
• Write the network parameter to the CPU module again.
• Execute again after correcting the offset of the device station link
device in the setting data.
• If the error occurs again even after taking the above, please
consult your local Mitsubishi representative.

D619H Parameter error • Write the network parameter to the CPU module again.
• If the error occurs again even after taking the above, please
consult your local Mitsubishi representative.

D61AH Parameter error • Write the network parameter to the CPU module again.
• If the error occurs again even after taking the above, please
consult your local Mitsubishi representative.

D61BH Parameter error (device overlap error (RWw)) • Write the network parameter to the CPU module again.
• Execute again after correcting the offset or size of the device
station link device in the setting data.
• If the error occurs again even after taking the above, please
consult your local Mitsubishi representative.

D61CH Parameter error (device overlap error (RWr)) • Write the network parameter to the CPU module again.
• Execute again after correcting the offset or size of the device
station link device in the setting data.
• If the error occurs again even after taking the above, please
consult your local Mitsubishi representative.

D61DH Parameter error (device overlap error (RY)) • Write the network parameter to the CPU module again.
• Execute again after correcting the offset or size of the device
station link device in the setting data.
• If the error occurs again even after taking the above, please
consult your local Mitsubishi representative.

D61EH Parameter error (device overlap error (RX)) • Write the network parameter to the CPU module again.
• Execute again after correcting the offset or size of the device
station link device in the setting data.
• If the error occurs again even after taking the above, please
consult your local Mitsubishi representative.

D61FH System error Please consult your local Mitsubishi representative. 
D621H Parameter error • Write the network parameter to the CPU module again.
• If the error occurs again even after taking the above, please
consult your local Mitsubishi representative.

D622H Parameter error (error in the total number of
device stations)
• Write the network parameter to the CPU module again.
• Execute again after correcting the total number of device stations.
• If the error occurs again even after taking the above, please
consult your local Mitsubishi representative.

D625H Parameter error (station-based block data
assurance setting error)
• Write the network parameter to the CPU module again.
• Execute again after correcting the station-based block data
assurance setting.
• If the error occurs again even after taking the above, please
consult your local Mitsubishi representative.

D628H Parameter error (station type error) • Write the network parameter to the CPU module again.
• Execute again after correcting the station type in the setting data.
• If the error occurs again even after taking the above, please
consult your local Mitsubishi representative.

Error
code
Error definition and causes Action Detailed
information 1
Detailed
information 2