Mitsubishi F700 Series User Manual

200
Selection of operation mode and
operation location
(3) Controllability through communication
*1 As set in Pr. 338 Communication operation command source and Pr. 339 Communication speed command source. (Refer to page 199)
*2 At occurrence of RS-485 communication error, the inverter cannot be reset from the computer.
*3 Enabled only when stopped by the PU. At a PU stop, PS is displayed on the operation panel. As set in Pr. 75 PU stop selection . (Refer to page 181)
*4 Some parameters may be write-disabled according to the Pr. 77 Parameter write selection setting and operating status. (Refer to page 184)
*5 Some parameters are write-enabled independently of the operation mode and command source presence/absence. When Pr. 77 = 2, write is
enabled. (Refer to page 56 for the parameter list)Parameter clear is disabled.
*6 When Pr. 550 NET mode operation command source selection = 1 (RS-485 terminals valid) or Pr. 550 NET mode operation command source selection =
9999 and the communication option is not fitted.
*7 When Pr. 550 NET mode operation command source selection = 0 (communication option valid) or Pr. 550 NET mode operation command source selection
= 9999 and the communication option is fitted.
Operation
Location
Condition
(Pr. 551
Setting)
Operation
Mode
Item
PU
Operation
External
Operation
External/PU
Combined
Operation Mode
1
(
Pr. 79 = 3)
External/PU
Combined
Operation
Mode 2
(Pr. 79 = 4)
NET Operation
(when RS-485
terminals are
used)
*6
NET Operation
(when
communication
option is used)
*7
Control by RS-485 communication from PU connector
2
(PU
connector)
Run command (start)    
Run command (stop)  *3  *3  *3
Running frequency
setting
   
Monitor    
Parameter write  *4  *5  *4  *4 *5
Parameter read    
Inverter reset    
Except for 2
Run command (start)    
Run command (stop)  *3  *3  *3  *3  *3
Running frequency
setting
   
Monitor    
Parameter write  *5  *5  *5  *5  *5
Parameter read    
Inverter reset    
Control by communication from
RS-485 terminals
1
(RS-485
terminals)
Run command(start,
stop)
   
Running frequency
setting
   
Monitor    
Parameter write  *4  *5  *4  *4  *5
Parameter read    
Inverter reset    
Except for 1
Run command
(start, stop)
    *1 
Running frequency
setting
    *1 
Monitor     
Parameter write *5 *5 *5 *5  *4 *5
Parameter read     
Inverter reset     *2 
Control by communication
from communication option

Run command
(start, stop)
     *1
Running frequency
setting
     *1
Monitor     
Parameter write *5 *5 *5 *5 *5  *4
Parameter read     
Inverter reset      *2
Control circuit
external terminals

Inverter reset    
Run command
(start, stop)
   *1
Frequency setting      *1
: Enabled, : Disabled,  : Some are enabled

Mitsubishi F700 Series Specifications

General

Humidity	95% RH or less (non-condensing)
Control Method	V/F control
Protection Features	Overcurrent, overvoltage, undervoltage, overheat, short circuit
Communication Options	RS-485
Operating Temperature	-10°C to +50°C
Storage Temperature	-20°C to +65°C
Altitude	Up to 1000m above sea level
Overload Capacity	150% for 60 seconds
Cooling Method	Forced air cooling
Power Range	0.75 to 630 kW (1 to 845 hp)
Output Voltage	3-phase 200 to 240 VAC, 380 to 500 VAC (matching input voltage)