EasyManuals Logo

NETGEAR GS752TP User Manual

NETGEAR GS752TP
275 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #111 background imageLoading...
Page #111 background image
Configuring Switching Information
111
GS752TP, GS728TP, and GS728TPP Gigabit Smart Switches
the Layer 2 LAN interface from its forwarding table entry upon receiving an IGMP
leave message for that Multicast group without first sending out MAC-based general
queries to the interface. You should enable fast leave admin mode only on VLANs
where only one host is connected to each Layer 2 LAN port. This mode prevents the
inadvertent dropping of the other hosts that were connected to the same Layer 2 LAN
port but were still interested in receiving multicast traffic directed to that group. Also,
fast leave processing is supported only with IGMP version 2 hosts.
Host T
imeout.
The value for group membership interval of IGMP snooping for the
specified VLAN ID. This value is calculated as follows: (Query Interval * 2) +
Maximum Response Time.
Maximum Response Time. Enter the amount of time in seconds that a switch waits
after sending a query on the VLAN because it did not receive a report for a particular
group in that interface.
The valid range is 5–20 seconds. This value must be less than
the Host Timeout value.
MRouter T
imeout
. The amount of time that a switch waits to receive a query on the
VLAN before removing it from the list of VLANs with multicast routers attached. This
value is calculated as follows: Query Interval * 2.
Query Mode. Enable or disable the IGMP querier mode for the specified VLAN ID.
Query Interval. Enter the value for IGMP query interval for the specified VLAN ID.
The valid range is 30–1800 seconds.
The default is 60 seconds.
3. Click APPLY to send the updated configuration to the switch.
Configuration changes take place immediately
.
To disable IGMP snooping on a VLAN and remove it from the list, select the check box next
to the VLAN ID and click DELETE.
IGMP Snooping Querier
IGMP snooping requires that one central switch or router periodically query all end devices
on the network to announce their Multicast memberships. This central device is the IGMP
querier. The IGMP query responses, known as IGMP reports, keep the switch updated with
the current multicast group membership on a port-by-port basis. If the switch does not
receive updated membership information in a timely fashion, it stops forwarding multicast
transmissions to the port where the end device is located.
The screens you access from the IGMP Snooping Querier link enable you to configure and
display information about IGMP snooping queriers on the network and, separately
, on
VLANs.
The IGMP Snooping Querier feature contains links to features described in the following
sections:
IGMP Snooping Querier Configuration
IGMP Snooping Querier VLAN Configuration
IGMP Snooping Querier VLAN Status

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NETGEAR GS752TP and is the answer not in the manual?

NETGEAR GS752TP Specifications

General IconGeneral
Switch typeManaged
Switch layerL3
Quality of Service (QoS) supportYes
Number of multicast groups filtered1024
Fiber optic connectorSFP
SFP module slots quantity4
Basic switching RJ-45 Ethernet ports typeGigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity48
10G support-
Number of VLANs256
Networking standardsIEEE 802.1D, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3af, IEEE 802.3at, IEEE 802.3x
Copper ethernet cabling technology1000BASE-T, 100BASE-T, 10BASE-T
DHCP featuresDHCP client
MAC address table8000 entries
Packet buffer memory8 MB
Number of static routes32
Supported network protocolsIPv4, IPv6, TFTP, SNTP, TACACS+
Power consumption (typical)384 W
SafetyCE, CSA, UL
Product colorGray
Electromagnetic compatibilityCE, FCC, Class A EN 55022, Class A C-Tick, EN 50082-1, EN 55024, CCC
Mean time between failures (MTBF)220447 h
Heat dissipation1750.70 BTU/h
Operating altitude0 - 3000 m
Storage temperature (T-T)-20 - 70 °C
Operating temperature (T-T)0 - 55 °C
Storage relative humidity (H-H)0 - 95 %
Operating relative humidity (H-H)10 - 90 %
Total Power over Ethernet (PoE) budget15.4 W
Power over Ethernet plus (PoE+) ports quantity8
Cables includedAC
Weight and Dimensions IconWeight and Dimensions
Depth316 mm
Width440 mm
Height43 mm
Weight5100 g

Related product manuals