NETGEAR GS752TP User Manual

Configuring System Information
46
GS752TP, GS728TP, and GS728TPP Gigabit Smart Switches
PoE Port Configuration
Use the PoE Port Configuration screen to configure PoE settings on the ports. The following
information is displayed for each port:
Table 9. PSE Port Information
Field Description
Admin Mode Indicates whether the port can deliver power (Enable) or cannot deliver
power (Disable).
Priority Level The switch might not be able to supply power to all connected devices.
Priority is used to determine which ports can supply power if power is
limited. When ports have the same priority
, the lower numbered port is given
a higher priority.
High Power Mode 802.3at.
Class Class of the powered device (PD) connected to the port.
The classes define
the range of maximum power output that the switch generates.
The power
level that the PD can actually use is slightly lower.
The classes are defined
as follows:
0. 0–15.4W
1. 0–4W
2. 0–7W
3. 0–15.4W
4. 0–30W.
Timer Schedule Indicates the timer schedule to use for the port. By default, no timer
schedules are configured.
Output Voltage (Volt) Displays the current voltage being delivered to device.
Output Current (mA) Displays the current being delivered to device.
Output Power (Watt) Displays the current power being delivered to the device.
Power Limit Displays the maximum amount of power limit that the port can generate. The
maximum amount is 15400 mW
.
Status Status of power being delivered by the port:
• Disabled. No power is being delivered.
• DeliveringPower. Power is being drawn by a connected device.
• Fault.
There is a problem with the port.
• Test. The port is in test mode.
• OtherFault. The port is idle due to an error condition.
• Searching. Port default state when PD not connected.
 To configure PoE on ports:
1. Select System
 PoE  Advanced  PoE Port Configuration.

NETGEAR GS752TP Specifications

General

Switch type	Managed
Switch layer	L3
Quality of Service (QoS) support	Yes
Number of multicast groups filtered	1024
Fiber optic connector	SFP
SFP module slots quantity	4
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	48
10G support	-
Number of VLANs	256
Networking standards	IEEE 802.1D, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3af, IEEE 802.3at, IEEE 802.3x
Copper ethernet cabling technology	1000BASE-T, 100BASE-T, 10BASE-T
DHCP features	DHCP client
MAC address table	8000 entries
Packet buffer memory	8 MB
Number of static routes	32
Supported network protocols	IPv4, IPv6, TFTP, SNTP, TACACS+
Power consumption (typical)	384 W
Safety	CE, CSA, UL
Product color	Gray
Electromagnetic compatibility	CE, FCC, Class A EN 55022, Class A C-Tick, EN 50082-1, EN 55024, CCC
Mean time between failures (MTBF)	220447 h
Heat dissipation	1750.70 BTU/h
Operating altitude	0 - 3000 m
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 55 °C
Storage relative humidity (H-H)	0 - 95 %
Operating relative humidity (H-H)	10 - 90 %
Total Power over Ethernet (PoE) budget	15.4 W
Power over Ethernet plus (PoE+) ports quantity	8
Cables included	AC

Weight and Dimensions

Depth	316 mm
Width	440 mm
Height	43 mm
Weight	5100 g