EasyManuals Logo

NETGEAR GS752TP User Manual

NETGEAR GS752TP
275 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #240 background imageLoading...
Page #240 background image
Maintenance
240
GS752TP, GS728TP, and GS728TPP Gigabit Smart Switches
2. In the Ping field, select either Global or Link Global to select either the global IPv6 Address
or host name or link local address to ping.
3. Optionally, configure the following settings:
In the IPv6 Address/Host Name field, enter the IPv6 address or host name of the
station you want the switch to ping.
The initial value is blank. The IPv6 address or
host name you enter is not retained across a power cycle. The valid range is 0–160
characters.
In the Datagram Size field, enter the datagram size.
The valid range is 48–2048.
The Result field displays the result after the switch sends a ping IPv6 request to the
specified IPv6 address.
4. Click APPL
Y to send the ping.
The switch sends the number of pings specified in the Count field, and the results are
displayed in the Results field.
If a reply to the ping is received, you see “Send count=3, Receive count =
n from
(IPv6 Address).A
verage round-trip time = n ms.”
If a reply to the ping is not received, you see “Reply From IP/Host: Destination
Unreachable. Tx = x, Rx = 0 Min/Max/A
vg RTT = 0/0/0 msec”.
Traceroute
Use the Traceroute utility to discover the paths that a packet takes to a remote destination.
To configure the Traceroute settings and send probe packets to discover the route to a
host on the network:
1. Select Maintenance Troubleshooting Traceroute.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NETGEAR GS752TP and is the answer not in the manual?

NETGEAR GS752TP Specifications

General IconGeneral
Switch typeManaged
Switch layerL3
Quality of Service (QoS) supportYes
Number of multicast groups filtered1024
Fiber optic connectorSFP
SFP module slots quantity4
Basic switching RJ-45 Ethernet ports typeGigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity48
10G support-
Number of VLANs256
Networking standardsIEEE 802.1D, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3af, IEEE 802.3at, IEEE 802.3x
Copper ethernet cabling technology1000BASE-T, 100BASE-T, 10BASE-T
DHCP featuresDHCP client
MAC address table8000 entries
Packet buffer memory8 MB
Number of static routes32
Supported network protocolsIPv4, IPv6, TFTP, SNTP, TACACS+
Power consumption (typical)384 W
SafetyCE, CSA, UL
Product colorGray
Electromagnetic compatibilityCE, FCC, Class A EN 55022, Class A C-Tick, EN 50082-1, EN 55024, CCC
Mean time between failures (MTBF)220447 h
Heat dissipation1750.70 BTU/h
Operating altitude0 - 3000 m
Storage temperature (T-T)-20 - 70 °C
Operating temperature (T-T)0 - 55 °C
Storage relative humidity (H-H)0 - 95 %
Operating relative humidity (H-H)10 - 90 %
Total Power over Ethernet (PoE) budget15.4 W
Power over Ethernet plus (PoE+) ports quantity8
Cables includedAC
Weight and Dimensions IconWeight and Dimensions
Depth316 mm
Width440 mm
Height43 mm
Weight5100 g

Related product manuals