NETGEAR GS752TP User Manual

Managing Device Security
205
GS752TP, GS728TP, and GS728TPP Gigabit Smart Switches
• Select keyword other from the drop-down list, and specify the number of the port.
The valid range is 0 - 65535.
• Select one of the keywords from the list: DOMAIN, ECHO, FTP, FTPDA
TA, HTTP,
SMTP, SNMP, TELNET, TFTP, and WWW. Each of these values translates into its
equivalent port number, which is used as both the start and end of a port range.
• Destination Prefix and Prefix Length. Enter a prefix of up to 128 bit combined with
prefix length to be compared to a packet's destination IP address as a match criteria
for the selected IPv6
ACL rule.
The valid range for a prefix length is 0 - 128.
• Destination L4 Port. Specify a packet's destination layer 4 port as a match condition
for the selected IPv6
ACL rule. Destination port information is optional. Destination
port information can be specified in two ways:
• Select keyword other
from the drop-down list, and specify the number of the port.
The valid range is 0 - 65535.
• Select one of the keywords from the list: DOMAIN, ECHO, FTP, FTPDA
TA, HTTP,
SMTP, SNMP, TELNET, TFTP, and WWW. Each of these values translates into its
equivalent port number, which is used as both the start and end of a port range.
• IPv6 DSCP Service. Select the IPv6 DSCP service. If you prefer, you can select the
Other
option in the drop-down list and enter the numeric value of the DSCP in the
adjacent field. The DSCP is defined as the high-order 6 bits of the service type octet
in the IPv6 header. This configuration is optional. Enter an integer from 0 to 63.
4. To add an IPv6 rule, select the global check box and click ADD.
T
o delete a IPv6 rule, select the checkbox of the rule you want to delete and click DELETE.
Click APPLY to submit the changes to the switch.
Configuration changes take ef
fect immediately.
IP Binding Configuration
When an ACL is bound to an interface, all the rules that have been defined are applied to the
selected interface. Use the IP Binding Configuration screen to assign ACL lists to ACL
Priorities and Interfaces.
 To configure IP ACL interface bindings:
1. Select Security
 ACL > Advanced  IP Binding Configuration.

NETGEAR GS752TP Specifications

General

Switch type	Managed
Switch layer	L3
Quality of Service (QoS) support	Yes
Number of multicast groups filtered	1024
Fiber optic connector	SFP
SFP module slots quantity	4
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	48
10G support	-
Number of VLANs	256
Networking standards	IEEE 802.1D, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3af, IEEE 802.3at, IEEE 802.3x
Copper ethernet cabling technology	1000BASE-T, 100BASE-T, 10BASE-T
DHCP features	DHCP client
MAC address table	8000 entries
Packet buffer memory	8 MB
Number of static routes	32
Supported network protocols	IPv4, IPv6, TFTP, SNTP, TACACS+
Power consumption (typical)	384 W
Safety	CE, CSA, UL
Product color	Gray
Electromagnetic compatibility	CE, FCC, Class A EN 55022, Class A C-Tick, EN 50082-1, EN 55024, CCC
Mean time between failures (MTBF)	220447 h
Heat dissipation	1750.70 BTU/h
Operating altitude	0 - 3000 m
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 55 °C
Storage relative humidity (H-H)	0 - 95 %
Operating relative humidity (H-H)	10 - 90 %
Total Power over Ethernet (PoE) budget	15.4 W
Power over Ethernet plus (PoE+) ports quantity	8
Cables included	AC

Weight and Dimensions

Depth	316 mm
Width	440 mm
Height	43 mm
Weight	5100 g