EasyManuals Logo

NETGEAR GS752TP User Manual

NETGEAR GS752TP
275 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #143 background imageLoading...
Page #143 background image
Configure Quality of Service
143
GS752TP, GS728TP, and GS728TPP Gigabit Smart Switches
priority or WRR priority. If a specific queue is configured as WRR, all the queues with
a lower number are also WRR queues. The configuration is global and not per port.
Weighted. Weighted round robin associates a weight to each queue. This
association is the default.
Strict. Services traffic with the highest priority on a queue first.
Queue Management Type. Displays the type of packet management used for all
packets, which is
T
aildrop. All packets on a queue are safe until congestion occurs. At
this point, any additional packets queued are dropped.
4. Click APPLY to apply the changes to the system.
802.1p to Queue Mapping
The 802.1p to Queue Mapping screen also displays the Current 802.1p Priority Mapping
table.
To map 802.1p priorities to queues:
1. Select QoS
CoS Advanced 802.1p to Queue Mapping.
The following screen displays:
2. Select the queue to which predefined 802.1p priority values are mapped.
The queue values represent traffic classes. The traffic class is the hardware queue for a
port. Higher traffic class values indicate a higher queue position. Before traffic in a lower
queue is sent, it must wait for traf
fic in higher queues to be sent.
Traffic classes go from low (0) to high (3). For example, traffic with a priority of 0 is for
most data traffic and is sent using best effort.
Traffic with a higher priority, such as 3,
might be time-sensitive traffic, such as voice or video.
3. Click APPLY to apply the changes to the system.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NETGEAR GS752TP and is the answer not in the manual?

NETGEAR GS752TP Specifications

General IconGeneral
Switch typeManaged
Switch layerL3
Quality of Service (QoS) supportYes
Number of multicast groups filtered1024
Fiber optic connectorSFP
SFP module slots quantity4
Basic switching RJ-45 Ethernet ports typeGigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity48
10G support-
Number of VLANs256
Networking standardsIEEE 802.1D, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3af, IEEE 802.3at, IEEE 802.3x
Copper ethernet cabling technology1000BASE-T, 100BASE-T, 10BASE-T
DHCP featuresDHCP client
MAC address table8000 entries
Packet buffer memory8 MB
Number of static routes32
Supported network protocolsIPv4, IPv6, TFTP, SNTP, TACACS+
Power consumption (typical)384 W
SafetyCE, CSA, UL
Product colorGray
Electromagnetic compatibilityCE, FCC, Class A EN 55022, Class A C-Tick, EN 50082-1, EN 55024, CCC
Mean time between failures (MTBF)220447 h
Heat dissipation1750.70 BTU/h
Operating altitude0 - 3000 m
Storage temperature (T-T)-20 - 70 °C
Operating temperature (T-T)0 - 55 °C
Storage relative humidity (H-H)0 - 95 %
Operating relative humidity (H-H)10 - 90 %
Total Power over Ethernet (PoE) budget15.4 W
Power over Ethernet plus (PoE+) ports quantity8
Cables includedAC
Weight and Dimensions IconWeight and Dimensions
Depth316 mm
Width440 mm
Height43 mm
Weight5100 g

Related product manuals