NF ZM2371 - Page 143

5.4 Command List
5-16 ZM2371/ZM2372
Table 5–3 Subsystem command list (1/3)
Command
Function / Operation target
ABORt subsystem
:ABORt
Aborts the measurement
CALCulate subsystem
:CALCulate:COMParator:AUXBin
Enables the use of auxiliary bins
:CALCulate:COMParator:BEEPer:CONDition
Beeper sounding condition
:CALCulate:COMParator:BEEPer[:STATe]
Enables the use of beeper
:CALCulate:COMParator:CLEar
Initializes comparator settings
:CALCulate:COMParator:MODE
Comparator primary parameter
comparison format
:CALCulate:COMParator:PRIMary:BIN{1|2|..|14}
Bin (primary parameter) lower & upper
limit values
:CALCulate:COMParator:PRIMary:BIN{1|2|..|14}:STATe
Enables bin sorting (primary parameter)
:CALCulate:COMParator:PRIMary:NOMinal
Reference value for primary parameter
deviation
:CALCulate:COMParator:SECondary:LIMit
Secondary parameter lower & upper
limit values
:CALCulate:COMParator:SECondary:STATe
Enables secondary parameter comparison
:CALCulate:COMParator[:STATe]
Enables the use of comparator
:CALCulate:COMParator:EXTension[:STATe]
Enables bin extended function 1
:CALCulate:FORMat:AUTO[:STATe]
Enables measurement parameter auto
selection
CALCulate1 subsystem
:CALCulate1:CKIT:AUTO[:STATe]
Enables equivalent circuit auto selection
:CALCulate1:FORMat
Selects primary parameter
:CALCulate1:LIMit:CLEar
Clears primary parameter comparator
result
:CALCulate1:LIMit:FAIL?
Queries primary parameter comparison
result
:CALCulate1:LIMit:LOWer[:DATA]
Primary parameter BIN1 lower limit
value
:CALCulate1:LIMit:LOWer:STATe
Enables primary parameter BIN1 lower
limit comparison
:CALCulate1:LIMit:STATe
Enables primary parameter BIN1 sorting
:CALCulate1:LIMit:UPPer[:DATA]
Primary parameter BIN1 upper limit
value
:CALCulate1:LIMit:UPPer:STATe
Enables primary parameter BIN1 upper
limit comparison
:CALCulate1:MATH:EXPRession:NAME
Primary parameter deviation display
format
:CALCulate1:MATH:STATe
Enables primary parameter deviation
display / output
CALCulate2 subsystem
:CALCulate2:FORMat
Selects secondary parameter
:CALCulate2:LIMit:CLEar
Clears secondary parameter
comparator result
:CALCulate2:LIMit:FAIL?
Queries secondary parameter
comparison result
:CALCulate2:LIMit:LOWer[:DATA]
Secondary parameter lower limit value
:CALCulate2:LIMit:LOWer:STATe
Enables secondary parameter lower
limit comparison
:CALCulate2:LIMit:STATe
Enables secondary parameter comparison
:CALCulate2:LIMit:UPPer[:DATA]
Secondary parameter upper limit value
:CALCulate2:LIMit:UPPer:STATe
Enables secondary parameter upper
limit comparison
:CALCulate2:MATH:EXPRession:NAME
Secondary parameter deviation display
format
:CALCulate2:MATH:STATe
Enables secondary parameter deviation
display / output
Supplement: The command that makes inquiry is called “query” and it terminates with a
question mark. In this table, the query is omitted in the functions capable of
making both setting and query.
1: Only for ZM2372. Unusable for ZM2371.