Nord Drivesystems B 1050 Series User Manual

3 Assembly instructions, storage, preparation, installation
B 1050 en-1819 53
Pos: 105 /A nleit ung en/G etr ieb e/3. Mo nt age, Lag eru ng, Vor ber eitung , Aufs tell ung /Ab tri ebs kup plu ng_ 01 [ B10 50, B 205 0] @ 3 2\mod_1553086483829_388.docx @ 2516388 @ 3 @ 1
3.22.2 Output coupling
Pos: 10 6 /Anlei tung en/G etrieb e/3. Mo ntag e, Lag erung , Vor berei tung , A ufs tell ung /Ab tri ebs kup plung _0 3 [ B10 50, B 205 0] @ 3 2\mod_1553086521973_388.docx @ 2516462 @ @ 1
NOTICE! Gear unit damage
Failure to observe the following points may result in damage to the gear unit.
• The alignment of pre-mounted output couplings must be checked according to the manufacturer's
documentation prior to commissioning.
• Output couplings which are supplied separately must be fitted and aligned according to the manufacturer's
documentation.
Pos: 10 7 /Anlei tu nge n/G etri ebe/ 3. M ont ag e, L ager ung , V orb ereit ung, A ufs tell ung/ Sens or ik z ur G etri eb eüb er wach ung_ 01 [ B10 50, B20 50] @ 3 0\mod_1552985980593_388.docx @ 2512391 @ 2 @ 1
3.23 Gear unit monitoring sensors
Pos: 10 8 /Anlei tung en/G etrieb e/3. Mo ntag e, Lager ung, V orber eitung , Aufs tell ung /Se ns ori k zur Getr i ebeü ber wac hung _0 3 [B 1050 , B2 050 ] @ 30\ mod_1552986887038_388.docx @ 2512465 @ @ 1
NOTICE!
Sensors
The following points must be observed for the use of sensors for monitoring the gear unit:
• The separate manufacturer’s documentation must be observed for assembly.
• The position of the sensors must be obtained from the specific dimension sheet for the order.
Pos: 10 9 /Anlei tung en/G etrieb e/3. Mo ntag e, Lager ung, V orber eitung, Aufs tellung /Nac hträgl iche L acki erung _01 [B1 050, B20 50] @ 30 \mod_1552987232682_388.docx @ 2512771 @ 2 @ 1
3.24 Subsequent paintwork
Pos: 11 0 /Anlei tung en/G etrieb e/3. Mo ntag e, Lager ung, V orber eitung, Aufs tellung /Nac hträgl iche L acki erung _03 [B1 050, B20 50] @ 30\ mod_1552987319637_388.docx @ 2512845 @ @ 1
NOTICE!
Gear unit damage
For retrospective painting of the gear unit, the shaft sealing rings, rubber elements, pressure vent screws, hoses,
type plates, adhesive labels and motor coupling components must not come into contact with paints, lacquers or
solvents, as otherwise the components may be damaged or made illegible.
Pos: 11 2 /Anlei tung en/G etrieb e/4. In betri ebna hme/4 . Inbetri ebn ahme [_Ti tel] @ 3\ mod_1368691822868_388.docx @ 65671 @ 1 @ 1

Nord Drivesystems B 1050 Series Specifications

General

Brand	Nord Drivesystems
Model	B 1050 Series
Category	Engine
Language	English