Oki B6200 - Page 389

3 – 225
Chapter 3 Removal and Replacement Procedures (RRPs)
34PPM
Removal
1) Remove the COVER REAR 500 (PL10.2.21). (RRP10.9)
2) Remove the COVER REAR (PL1.1.3). (RRP1.1)
3) Remove the FUSER ASSY (PL8.1.20). (RRP8.8)
4) Remove the COVER LEFT (PL1.1.6). (RRP1.3)
5) Remove the COVER RIGHT (PL1.1.4). (RRP1.2)
6) Remove the COVER EXIT 500 (PL10.1.1). (RRP10.1)
7) Remove the 500 EXIT ASSY (PL10.1.2). (RRP10.2)
8) Remove the COVER TOP (PL1.1.7). (RRP1.4)
9) Remove the COVER FRONT (PL1.1.5). (RRP1.5)
10) Remove the BTR ASSY (PL8.1.21). (RRP8.10)
11) Remove the DUCT FRONT (PL8.1.4). (RRP8.2)
12) Remove the ROS ASSY (PL8.1.1). (RRP8.1)
Never give any impact to the ROS ASSY with a screwdriver or other tools.
13) Remove the SHIELD PLATE ROS (PL8.1.3). (RRP8.3)
14) Remolve the GUIDE TRAY LEFT (PL7.1.7). (RRP7.8)
15) Remove the MOTOR COVER (PL11.1.1). (RRP11.1)
16) Remove the SHIELD PLATE LVPS (PL12.1.3). (RRP12.1)
17) Remove the GUIDE CRU LEFT (PL8.1.15). (RRP8.4)
18) Remove the COVER GUIDE CRU (PL8.1.16) and HARNESS ASSY FUSER (PL8.1.17) from the
GUIDE CRU LEFT. (RRP8.7)
19) Remove the INTERLOCK S/W 24V (PL8.1.11) and INTERLOCK S/W 5V (PL8.1.12). (RRP8.5)
20) Remove the SPRING SL (PL8.1.9) from the GUIDE CRU LEFT.
21) Remove the SPACER SS (PL8.1.8) from the GUIDE CRU LEFT.
22) Remove the GUIDE SL (PL8.1.7) from the GUIDE CRU LEFT.
23) Remove the LEVER GUIDE from the GUIDE CRU LEFT.
Replacement
1) Install the LEVER GUIDE to the GUIDE CRU LEFT(PL8.1.15).
2) Install the GUIDE SL (PL8.1.7) to the GUIDE CRU LEFT.
3) Install the SPACER SS (PL8.1.8) to the GUIDE CRU LEFT.
4) Install the SPRING SL (PL8.1.9) to the GUIDE CRU LEFT.
5) Install the INTERLOCK S/W 24V (PL8.1.11) and INTERLOCK S/W 5V (PL8.1.12). (RRP8.5)
6) Install the COVER GUIDE CRU (PL8.1.16) and HARNESS ASSY FUSER (PL8.1.17). (RRP8.7)
7) Install the GUIDE CRU LEFT (PL8.1.15). (RRP8.4)
When installing, make sure that the LEVER LINK (PL8.1.29) is attached to the
GUIDE CRU LEFT.
After installing the GUIDE CRU LEFT, touch the LINK GEAR 3 with your finger.
Make sure that your finger can feel the LINK GEAR 3 move inward, when the LEVER
LINK is pulled up.
8) nstall the SHIELD PLATE LVPS (PL12.1.3). (RRP12.1)
9) Install the MOTOR COVER (PL11.1.1). (RRP11.1)
10) Install the GUIDE TRAY LEFT (PL7.1.7). (RRP7.8)
11) Install the SHIELD PLATE ROS (PL8.1.3). (RRP8.3)