Oki B6200 - Page 416

3 – 252
Chapter 3 Removal and Replacement Procedures (RRPs)
Removal
1) Remove the COVER REAR 500/COVER REAR 250 (PL10.2.21/9.1.12). (RRP10.9/9.4)
2) Remove the COVER REAR (PL1.1.3). (RRP1.1)
3) Remove the FUSER ASSY (PL8.1.20). (RRP8.8)
4) Remove the COVER LEFT (PL1.1.6). (RRP1.3)
5) Remove the COVER RIGHT (PL1.1.4). (RRP1.2)
6) Remove the COVER EXIT 500 (PL10.1.1)/CHUTE ASSY EXIT 250 (Reference Only) (PL9.1.14).
(RRP10.1/9.7)
7) Remove the 500 EXIT ASST (PL10.1.2)/CHUTE LW EXT2 ASSY (PL9.1.2). (RRP10.2/9.1)
8) Remove the COVER TOP (PL1.1.7). (RRP1.4)
9) Remove the COVER FRONT (PL1.1.5). (RRP1.5)
10) Remove the BTR ASSY (PL8.1.21). (RRP8.10)
11) Remove the SHIELD ASSY ESS (PL12.1.14). (RRP12.7)
12) Remove the SHIELD PLATE HVPS (PL12.1.18). (RRP12.9)
13) Remove the DUCT FRONT (PL8.1.4). (RRP8.2)
14) Disconnect the connector (P/J31) of the GUIDE ASSY CRU R from the HVPS/MCU (PL12.1.19).
15) Disconnect the connector (P/J15) of the HARNESS ASSY ANT from the HVPS/MCU.
16) Remove the 3 screws (silver, 6mm) securing the GUIDE ASSY CRU R to the frame.
17) Pull out the harness of the GUIDE ASSY CRU R from the frame.
18) Remove the GUIDE ASSY CRU R.
Replacement
1) Install the GUIDE ASSY CRU R.
2) Put the harness of the GUIDE ASSY CRU R to the hole of the frame.
3) Install the GUIDE ASSY CRU R to the frame using the 3 screws (silver, 6mm).
4) Connect the connector (P/J15) of the HARNESS ASSY ANT to the HVPS/MCU (PL12.1.19).
5) Connect the connector (P/J31) of the GUIDE ASSY CRU R to the HVPS/MCU.
6) Install the DUCT FRONT (PL8.1.4). (RRP8.2)
7) Install the SHIELD PLATE HVPS (PL12.1.18). (RRP12.9)
8) Install the SHIELD ASSY ESS (PL12.1.14). (RRP12.7)
9) Install the COVER FRONT (PL1.1.5). (RRP1.5)
10) Install the COVER TOP (PL1.1.7). (RRP1.4)
11) Install the 500 EXIT ASST (PL10.1.2)/CHUTE LW EXT2 ASSY (PL9.1.2). (RRP10.2/9.1)
12) Install the COVER EXIT 500 (PL10.1.1)/CHUTE ASSY EXIT 250 (Reference Only) (PL9.1.14).
(RRP10.1/9.7)
13) Install the COVER RIGHT (PL1.1.4). (RRP1.2)
14) Install the COVER LEFT (PL1.1.6). (RRP1.3)
15) Install the FUSER ASSY (PL8.1.20). (RRP8.8)
16) Install the COVER REAR (PL1.1.3). (RRP1.1)
There are 2 kinds of screws, make sure they are put in the right place.
17) Install the COVER REAR 500/COVER REAR 250 (PL10.2.21/9.1.12). (RRP10.9/9.4)
18) Install the BTR ASSY (PL8.1.21). (RRP8.10)