Oki Data CONFIDENTIAL
45487001TH Rev.1
4-13 /
4. Maintenance menus
Item Settings Functions
Admin Setup PCL
Setup
CR Function CR
CR+LF
Sets performance when CR code is
received in PCL.
CR: Carriage Return
CR+LF: Carriage Return and Line Feed
LF Function
LF
LF+CR
Sets performance when LF code is
received in PCL.
LF: Line Feed
LF+CR: Line Feed and Carriage Return
Print Margin
Normal
1/5 inch
1/6 inch
1/12.5 inch
Sets a non-printable area of paper.
The width of the area along the right and
left sides of paper (left and right of paper
laid out according to paper orientation)
paper outside the printable area
NORMAL: PCL emulation compatible,
approximately 1/4~1/4.3INCH (depending
on paper) is outside the printable area.
The option "1/12.5 inch" only be displayed
when Edge to Edge function was enabled.
Pen Width
Adjust
On
Off
When the minimum width is specified in
PCL, if you draw a 1-dot line, it sometimes
looks broken.
With PEN WIDTH Adjust set to ON, when
the minimum width is specified, the line
width will be emphasized so as to look
wider than a 1-dot line.
Tr ay
ID#
MP
Tr ay
1
~
4
~
59
Sets the # to specify the MPTray for
the paper feed destination command
(ESC&l#H) in PCL5e emulation.
Tr ay 1
1
~
59
Sets the # to specify Tray 1 for the paper
feed destination command (ESC&l#H) in
PCL5e emulation.
Tr ay 2
1
~
5
~
59
Sets the # to specify Tray 2 for the paper
feed destination command (ESC&l#H) in
PCL5e emulation. Displayed only if the
Tray 2 is installed.
Item Settings Functions
Admin Setup PCL
Setup
Tr ay
ID#
Tr ay 3 1
~
20
~
59
Sets the # to specify Tray 3 for the paper
feed destination command (ESC&l#H) in
PCL5e emulation. Displayed only if the
Tray 3 is installed.
Tr ay 4
1
~
21
~
59
Sets the # to specify Tray 4 for the paper
feed destination command (ESC&l#H) in
PCL5e emulation. Displayed only if the
Tray 4 is installed.
XPS
Setup
Digital-
Signature
Print Invalid Sign
PrintOnlyValidSign
Off
Sets up the DigitalSignature function.
Print Invalid Sign: If a document has been
tampered, the printer prints a normal print
report and a temper error report.
Print Only Valid Sign: If a document has
been tampered, the printer prints only a
tamper error report.
Off: No signatures are verified.
Discard-
Control
Auto
Each Page
Off
Sets up the DiscardControl function.
Auto: Frees resources as necessary.
EachPage: Frees resources page by page
according to markups.
Off: Disables the DiscardControl function.
MC Mode
On
Off
Sets up the MarkupComaptibility function.
On: Uses the MarkupComaptibility
function.
Off: Not use the MarkupComaptibility
function.
Unzip Mode
Auto
Speed
Print
Specifies the unzip method for XPS flies.
Auto: Automatically switches modes
depending on files.
Speed: Prioritizes print speed and doesn't
use the partial Unzip function.
Print: Prioritizes print processing and uses
the partial Unzip function.
White Page
Skip
On
Off
Sets whether or not to eject pages that
contain no print data (blank pages) using
XPS.
When Off is selected, blank pages are
ejected, if any.
To Next Page
Loading...
Need help?
General
