Powerscreen XA750S

To Next Page

To Previous Page

AM0009-2

Fuel Transfer Pump [if 󰘰tted]

1. DO NOT USE A TRIGGER NOZZLE FOR

DELIVERY INTO THE FUEL TANK.

2. FLASHPOINT BELOW 37°C (99°F)

PETROL

GASOLINE

BENZINE

3. FLASHPOINT ABOVE 37°C (99°F)

DIESEL

GAS OIL

FUEL OIL

SAFETY

Main Page

Default Chapter5
- Table of Contents5
EN Introduction11
- Introduction to User Manual12
- Safety Warnings and Symbols13
- Designated Use of Machine14
- Additional Information and Features15
- AM0009 Fuel Transfer Pumps [EN]17
- AM0010 M.C.S. Belt Weigher BW100 [EN]21
- AM0011 Water Pump [EN]27
EN Safety Notices and Hazards31
- Safety Notices32
- Safety Information36
- Organisation Measures37
- Selection and Qualification of Personnel - Basic Responsibilities38
- Safety Instructions Governing Specific Operational Phases39
- Warning of Special Dangers42
- Safety Signs46
EN General Information59
- General60
- EC Conformity60
- Units of Measure61
- Copyright61
- Operating Temperature62
- Information and Advice62
EN Plant Specification and Information63
- Dimensions64
- Plant Description65
- Weights65
- Plant Components66
- Jaw Crusher70
EN General Screen Icons71
- Plant Icons72
EN Preparing to Move the Plant75
- Initial Preparation76
- Preparing for Loading [Engine Stopped]77
- Product Conveyor79
- Dirt Conveyor [If Fitted]82
- Hopper84
- Safety Grid85
- Maintenance Platforms86
- Secure Loose Items87
- Set Plant to Track Mode88
EN Unloading and Loading - Transport Trailer91
- Unloading from Trailer92
- Loading on to Trailer93
EN Moving the Machine ['860' Control]95
- Moving the Machine on the Tracks96
- Initial Preparation96
- Preparing Umbilical Control97
- Preparing Radio Control [If Fitted]98
- Manoeuvring the Machine100
- Finish Manoeuvring the Machine104
EN '860' Radio Remote Control105
- Operation [If Fitted]106
- Battery Recharging107
- Battery Replacement108
EN Engine Stop109
- Switching off Engine110
EN Emergency Stop113
- Emergency Stopping the Machine114
- Re-Setting Emergency Stops115
- Testing Emergency Stops116
EN Preparing to Crush117
- Plant Location Considerations118
- Initial Preparation119
- Hopper121
- Secure Hopper122
- Dirt Conveyor [If Fitted]123
EN Dust Suppression System169
- Dust Suppression Water Spray System170
27 Feeder Stop and Start ['860' Radio Remote]179
- EN Preparing to Finish Crushing179
EN Clearing a Stalled Jaw Crusher185
- Stalled Jaw Crusher186
  - EN Initial Checks - Running in189
- Actions During Running-In Period191
  - EN Jaw Crusher Checks193
- Wear Checks194
- Routine Inspection Checks196
EN Servicing Safety and Precautions197
- Servicing Safety Information198
EN Servicing - Lubrication205
- Lubrication Requirements206
- Lubrication and Hydraulic System Schedule208
- Ambient Temperature Variations214
EN Lubricant and Fluid Specifications215
- Lubricant Oil Specifications216
- Grease Specifications218
- Hydraulic Fluid Specifications220
EN Servicing Vibrating Hopper Feeder221
- Vibrating Hopper Feeder - Servicing222
EN Servicing Jaw Crusher225
- Jaw Crusher Lubrication226
EN Servicing Vee Belts227
- General228
- Alignment229
- Adjustment230
- Replacement233
- Drive Belt Tension234
- Fault Finding236
EN Servicing Conveyors237
- Magnetic Separator238
- Training of Belts239
- Conveyor Belt Tensioning240
- Inspection of Conveyors242
- Lubrication244
- Cleaning Conveyor Belts245
EN Servicing of Tracks247
- Adjusting Track Tension250
- Drive Oil Draining & Filling252
EN Servicing Clutch Type 'G255
- Engine Power Transmission256
EN Servicing Magnetic Separator257
- Magnetic Separator - General258
  - [If Fitted]258
- Inspection258
- Servicing259
  - EN Servicing Electrical System261
- Battery Replacement263
  - EN Servicing Hydraulic System267
- Hydraulic Fluid Level269
- Suction Filter270
- Return Filter272
- Tank Breather273
- Pressure Filters274
  - EN Replacing Worn Jaws275

Powerscreen XA750S - Page 18

Table of Contents