Powerscreen XA750S - Lubrication and Hydraulic System Schedule

292 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

41-4

P10

P3

P8 P9

P8

P9

P11

P10

P11

P2

P2

P4

P4

P5

P5

P6

P6

P7

P7

P12

P12

P13

P13

P13

P13

P13

P13

P13

P1

P1

P13

P14

P14

Servicing - Lubrication

Lubrication and Hydraulic System Schedule

Table of Contents

Default Chapter5
- Table of Contents5
EN Introduction11
- Introduction to User Manual12
- Safety Warnings and Symbols13
- Designated Use of Machine14
- Additional Information and Features15
- AM0009 Fuel Transfer Pumps [EN]17
- AM0010 M.C.S. Belt Weigher BW100 [EN]21
- AM0011 Water Pump [EN]27
EN Safety Notices and Hazards31
- Safety Notices32
- Safety Information36
- Organisation Measures37
- Selection and Qualification of Personnel - Basic Responsibilities38
- Safety Instructions Governing Specific Operational Phases39
- Warning of Special Dangers42
- Safety Signs46
EN General Information59
- General60
- EC Conformity60
- Units of Measure61
- Copyright61
- Operating Temperature62
- Information and Advice62
EN Plant Specification and Information63
- Dimensions64
- Plant Description65
- Weights65
- Plant Components66
- Jaw Crusher70
EN General Screen Icons71
- Plant Icons72
EN Preparing to Move the Plant75
- Initial Preparation76
- Preparing for Loading [Engine Stopped]77
- Product Conveyor79
- Dirt Conveyor [If Fitted]82
- Hopper84
- Safety Grid85
- Maintenance Platforms86
- Secure Loose Items87
- Set Plant to Track Mode88
EN Unloading and Loading - Transport Trailer91
- Unloading from Trailer92
- Loading on to Trailer93
EN Moving the Machine ['860' Control]95
- Moving the Machine on the Tracks96
- Initial Preparation96
- Preparing Umbilical Control97
- Preparing Radio Control [If Fitted]98
- Manoeuvring the Machine100
- Finish Manoeuvring the Machine104
EN '860' Radio Remote Control105
- Operation [If Fitted]106
- Battery Recharging107
- Battery Replacement108
EN Engine Stop109
- Switching off Engine110
EN Emergency Stop113
- Emergency Stopping the Machine114
- Re-Setting Emergency Stops115
- Testing Emergency Stops116
EN Preparing to Crush117
- Plant Location Considerations118
- Initial Preparation119
- Hopper121
- Secure Hopper122
- Dirt Conveyor [If Fitted]123
EN Dust Suppression System169
- Dust Suppression Water Spray System170
27 Feeder Stop and Start ['860' Radio Remote]179
- EN Preparing to Finish Crushing179
EN Clearing a Stalled Jaw Crusher185
- Stalled Jaw Crusher186
  - EN Initial Checks - Running in189
- Actions During Running-In Period191
  - EN Jaw Crusher Checks193
- Wear Checks194
- Routine Inspection Checks196
EN Servicing Safety and Precautions197
- Servicing Safety Information198
EN Servicing - Lubrication205
- Lubrication Requirements206
- Lubrication and Hydraulic System Schedule208
- Ambient Temperature Variations214
EN Lubricant and Fluid Specifications215
- Lubricant Oil Specifications216
- Grease Specifications218
- Hydraulic Fluid Specifications220
EN Servicing Vibrating Hopper Feeder221
- Vibrating Hopper Feeder - Servicing222
EN Servicing Jaw Crusher225
- Jaw Crusher Lubrication226
EN Servicing Vee Belts227
- General228
- Alignment229
- Adjustment230
- Replacement233
- Drive Belt Tension234
- Fault Finding236
EN Servicing Conveyors237
- Magnetic Separator238
- Training of Belts239
- Conveyor Belt Tensioning240
- Inspection of Conveyors242
- Lubrication244
- Cleaning Conveyor Belts245
EN Servicing of Tracks247
- Adjusting Track Tension250
- Drive Oil Draining & Filling252
EN Servicing Clutch Type 'G255
- Engine Power Transmission256
EN Servicing Magnetic Separator257
- Magnetic Separator - General258
  - [If Fitted]258
- Inspection258
- Servicing259
  - EN Servicing Electrical System261
- Battery Replacement263
  - EN Servicing Hydraulic System267
- Hydraulic Fluid Level269
- Suction Filter270
- Return Filter272
- Tank Breather273
- Pressure Filters274
  - EN Replacing Worn Jaws275