ProMinent DULCOMETER - Page 180

ProMinent DULCOMETER

180 pages

Save Page as PDF

To Previous Page

To Previous Page

Loading...

985250, 4, en_GB

© 2014

ProMinent GmbH

Im Schuhmachergewann 5 - 11

69123 Heidelberg

Telephone: +49 6221 842-0

Fax: +49 6221 842-419

email: info@prominent.com

Internet: www.prominent.com

The latest version of the operating instructions are available on our homepage.

Table of Contents

Default Chapter3
- Table of Contents3
1 Operating Concept8
- Functions of the Keys11
- Changes the Set Operating Language12
- Acknowledging Error or Warning Messages13
- Key Lock13
2 Entries in the [Menu] Display14
3 ID Code15
- A Complete Measuring Station May Comprise the Following17
4 Safety and Responsibility18
- Explanation of the Safety Information18
- General Safety Notes19
- Intended Use20
- Users' Qualifications21
5 Functional Description23
6 Assembly and Installation24
- Scope of Supply26
- Mechanical Installation26
- Wall Mounting26
- Control Panel Installation28
- Electrical Installation31
- Specification of the Threaded Connectors32
- Terminal Diagram33
- Cable Cross-Sections and Cable End Sleeves42
- Wall Mounting and Control Panel Installation43
- Switching of Inductive Loads44
- Connect the Sensors Electrically to the Controller45
- Priming to Bleeding49
7 Commissioning50
- Switch-On Behaviour During Commissioning50
- Adjusting the Backlight and Contrast of the Controller Display51
- Resetting the Operating Language51
- Defining Metering and Control Processes51
8 Setting Measured Variables52
- Information on the Measured Variables54
- Measured Variable Ph [MV]54
- Temperature54
- Measured Variable Ph [Ma]55
- ORP [MV], ORP [Ma]55
- Chlorine, Bromine, Chlorine Dioxide, Chlorite, Dissolved Oxygen and Ozone56
- Fluoride Measured Variable58
- Peracetic Acid58
- Hydrogen Peroxide59
- Conductivity [Ma]59
- Temperature [Ma], (as Main Measured Variable)59
- Ma General60
- Features of the Two-Channel Version60
9 Calibration61
- Calibrating the Ph Sensor62
- Selecting the Calibration Process for Ph65
- 2-Point Ph Sensor Calibration (CAL)66
- Ph Sensor Calibration (CAL) with an External Sample (1-Point)70
- Calibration of the Ph Sensor (CAL) by [Data Input]73
- Calibrating the ORP Sensor76
- Selecting the Calibration Process for ORP76
- 1-Point Calibration of ORP Sensor (CAL)76
- Calibration Data for ORP Sensor (CAL)78
- Calibrating the Fluoride Sensor80
- Selection of the Calibration Process for Fluoride80
- 2-Point Fluoride Sensor Calibration (CAL)80
- 1-Point Fluoride Sensor Calibration (CAL)82
- Calibrating Amperometric Sensors84
- Selecting the Calibration Process for Amperometric Measured Variables85
- Calibrating the Slope85
- Calibration of Zero Point88
- Calibrating Oxygen Sensors90
- Selection of the Calibration Process for the Measured Variable O91
- Selection of the Calibration Process for the Measured Variable DO92
- Zero Point Calibration for the Measured Variable DO94
- DO Value Calibration for the Measured Variable DO96
- Measured Value [Ma General] Calibration98
- Calibrating Conductivity98
- Calibrating Temperature99
10 Setting the [Control]101
- Control Parameter [Type]108
- Control Parameter [System Response]109
- Control Parameter [Setpoint]109
- Control Parameter [Xp]110
- Control Parameter [Ti]111
- Control Parameter [Td]111
- Control Parameter [Add. Basic Load]111
- Control Parameter [Checkout Time]111
- Control Parameter [Max. Ctrl Var.]111
- Interference Variable111
- Remote Setpoint Via a 0/4114
- Parameter Switch] Via the Digital Input or [Timer]116
11 Setting the [Limit Values]120
- Function of the Limit Values120
- Setting Limit Value Channel 1122
- Setting [Limit 1]123
- Setting [Limit 2]123
- Setting [System Response]124
12 Setting the [Pumps]125
- Setting [Pump 1]125
13 Setting the [Relays]128
- Setting Relay 1128
- Function Description [Off]131
- Functional Description of [Relay Timer]131
- Function Description [Limit 1] or [Limit 2]131
- Functional Description of [Limit Value 1/2 (Control Variable)]131
- Function Description of [Cycle]131
- Functional Description of [Pulse Length (PWM)]132
14 Setting [Digital Inputs]133
- Setting [Digital Input 1]133
15 Setting the [Ma Outputs]136
- Setting the [Ma Outputs]138
16 Function: Data Logger140
- Activating, Reading and Deleting Log Books140
- Configuring Log Books141
- Using the [Calibration Log Book]141
- Using the [Error Log Book]142
- Using the [Data Log Book] (Optional)143
17 Diagnostics146
- Displaying [Logbooks]146
- Displaying the [Calibration Log Book]146
- Reading the [Error Log Book]146
- Displaying [Simulation]147
- Displaying [Device Information]147
- Error Messages and Warning Alerts148
- Help Texts155
18 Service157
- Setting the [Wash Timer]157
19 Setting [Device Setup]158
- Setting the [Language]159
- Setting [Device Configuration]160
- Setting the [Extended Configuration]160
- Update161
- Setting the [Access Code]162
20 Controller Technical Data163
21 Spare Parts and Accessories166
- Spare Parts166
- Accessories167
22 Required Formalities168
- Disposal of Used Parts168
- Standards Complied with and Conformity Declaration168

Other manuals for ProMinent DULCOMETER

Installation And Configuration Manual92 pages

Related product manuals

Preview: ProMinent DULCOMETER D1Cb

ProMinent DULCOMETER D1Cb

Preview: ProMinent DULCOMETER D1CA

ProMinent DULCOMETER D1CA

ProMinent DULCOMETER D1Cc

Preview: ProMinent DULCOMETER Compact

ProMinent DULCOMETER Compact

Preview: ProMinent DULCOMETER diaLog DACb

ProMinent DULCOMETER diaLog DACb

Preview: ProMinent DULCOMARIN II

ProMinent DULCOMARIN II

Preview: ProMinent diaLog DACb

ProMinent diaLog DACb

Preview: ProMinent DCM3 Series

ProMinent DCM3 Series

Preview: ProMinent DCM 5 Series

ProMinent DCM 5 Series

Preview: ProMinent DCM 2 Series

ProMinent DCM 2 Series

Preview: ProMinent DULCOMETER D1C

ProMinent DULCOMETER D1C

Preview: ProMinent DULCOMETER DMT Series

ProMinent DULCOMETER DMT Series