ProMinent DULCOMETER - Specification of the Threaded Connectors

ProMinent DULCOMETER

180 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

6.3.1 Specification of the threaded connectors

A1066

Fig. 12: All dimensions in millimetres (mm)

A1067

Fig. 13: All dimensions in millimetres (mm)

Assembly and installation

32

Table of Contents

Default Chapter3
- Table of Contents3
1 Operating Concept8
- Functions of the Keys11
- Changes the Set Operating Language12
- Acknowledging Error or Warning Messages13
- Key Lock13
2 Entries in the [Menu] Display14
3 ID Code15
- A Complete Measuring Station May Comprise the Following17
4 Safety and Responsibility18
- Explanation of the Safety Information18
- General Safety Notes19
- Intended Use20
- Users' Qualifications21
5 Functional Description23
6 Assembly and Installation24
- Scope of Supply26
- Mechanical Installation26
- Wall Mounting26
- Control Panel Installation28
- Electrical Installation31
- Specification of the Threaded Connectors32
- Terminal Diagram33
- Cable Cross-Sections and Cable End Sleeves42
- Wall Mounting and Control Panel Installation43
- Switching of Inductive Loads44
- Connect the Sensors Electrically to the Controller45
- Priming to Bleeding49
7 Commissioning50
- Switch-On Behaviour During Commissioning50
- Adjusting the Backlight and Contrast of the Controller Display51
- Resetting the Operating Language51
- Defining Metering and Control Processes51
8 Setting Measured Variables52
- Information on the Measured Variables54
- Measured Variable Ph [MV]54
- Temperature54
- Measured Variable Ph [Ma]55
- ORP [MV], ORP [Ma]55
- Chlorine, Bromine, Chlorine Dioxide, Chlorite, Dissolved Oxygen and Ozone56
- Fluoride Measured Variable58
- Peracetic Acid58
- Hydrogen Peroxide59
- Conductivity [Ma]59
- Temperature [Ma], (as Main Measured Variable)59
- Ma General60
- Features of the Two-Channel Version60
9 Calibration61
- Calibrating the Ph Sensor62
- Selecting the Calibration Process for Ph65
- 2-Point Ph Sensor Calibration (CAL)66
- Ph Sensor Calibration (CAL) with an External Sample (1-Point)70
- Calibration of the Ph Sensor (CAL) by [Data Input]73
- Calibrating the ORP Sensor76
- Selecting the Calibration Process for ORP76
- 1-Point Calibration of ORP Sensor (CAL)76
- Calibration Data for ORP Sensor (CAL)78
- Calibrating the Fluoride Sensor80
- Selection of the Calibration Process for Fluoride80
- 2-Point Fluoride Sensor Calibration (CAL)80
- 1-Point Fluoride Sensor Calibration (CAL)82
- Calibrating Amperometric Sensors84
- Selecting the Calibration Process for Amperometric Measured Variables85
- Calibrating the Slope85
- Calibration of Zero Point88
- Calibrating Oxygen Sensors90
- Selection of the Calibration Process for the Measured Variable O91
- Selection of the Calibration Process for the Measured Variable DO92
- Zero Point Calibration for the Measured Variable DO94
- DO Value Calibration for the Measured Variable DO96
- Measured Value [Ma General] Calibration98
- Calibrating Conductivity98
- Calibrating Temperature99
10 Setting the [Control]101
- Control Parameter [Type]108
- Control Parameter [System Response]109
- Control Parameter [Setpoint]109
- Control Parameter [Xp]110
- Control Parameter [Ti]111
- Control Parameter [Td]111
- Control Parameter [Add. Basic Load]111
- Control Parameter [Checkout Time]111
- Control Parameter [Max. Ctrl Var.]111
- Interference Variable111
- Remote Setpoint Via a 0/4114
- Parameter Switch] Via the Digital Input or [Timer]116
11 Setting the [Limit Values]120
- Function of the Limit Values120
- Setting Limit Value Channel 1122
- Setting [Limit 1]123
- Setting [Limit 2]123
- Setting [System Response]124
12 Setting the [Pumps]125
- Setting [Pump 1]125
13 Setting the [Relays]128
- Setting Relay 1128
- Function Description [Off]131
- Functional Description of [Relay Timer]131
- Function Description [Limit 1] or [Limit 2]131
- Functional Description of [Limit Value 1/2 (Control Variable)]131
- Function Description of [Cycle]131
- Functional Description of [Pulse Length (PWM)]132
14 Setting [Digital Inputs]133
- Setting [Digital Input 1]133
15 Setting the [Ma Outputs]136
- Setting the [Ma Outputs]138
16 Function: Data Logger140
- Activating, Reading and Deleting Log Books140
- Configuring Log Books141
- Using the [Calibration Log Book]141
- Using the [Error Log Book]142
- Using the [Data Log Book] (Optional)143
17 Diagnostics146
- Displaying [Logbooks]146
- Displaying the [Calibration Log Book]146
- Reading the [Error Log Book]146
- Displaying [Simulation]147
- Displaying [Device Information]147
- Error Messages and Warning Alerts148
- Help Texts155
18 Service157
- Setting the [Wash Timer]157
19 Setting [Device Setup]158
- Setting the [Language]159
- Setting [Device Configuration]160
- Setting the [Extended Configuration]160
- Update161
- Setting the [Access Code]162
20 Controller Technical Data163
21 Spare Parts and Accessories166
- Spare Parts166
- Accessories167
22 Required Formalities168
- Disposal of Used Parts168
- Standards Complied with and Conformity Declaration168

Other manuals for ProMinent DULCOMETER

Installation And Configuration Manual92 pages

Related product manuals

Preview: ProMinent DULCOMETER D1Cb

ProMinent DULCOMETER D1Cb

Preview: ProMinent DULCOMETER D1CA

ProMinent DULCOMETER D1CA

ProMinent DULCOMETER D1Cc

Preview: ProMinent DULCOMETER Compact

ProMinent DULCOMETER Compact

Preview: ProMinent DULCOMETER diaLog DACb

ProMinent DULCOMETER diaLog DACb

Preview: ProMinent DULCOMARIN II

ProMinent DULCOMARIN II

Preview: ProMinent diaLog DACb

ProMinent diaLog DACb

Preview: ProMinent DCM3 Series

ProMinent DCM3 Series

Preview: ProMinent DCM 5 Series

ProMinent DCM 5 Series

Preview: ProMinent DCM 2 Series

ProMinent DCM 2 Series

Preview: ProMinent DULCOMETER D1C

ProMinent DULCOMETER D1C

Preview: ProMinent DULCOMETER DMT Series

ProMinent DULCOMETER DMT Series