Need help?Do you have a question about the Rational SCC Line and is the answer not in the manual?
General| Category | Grill |
|---|---|
| Material | Stainless steel |
| Line | SCC Line |
| Grill Surface Temperature | Up to 300°C |
| Grill Surface Area | Varies by model |
Overview of the CM control panel layout and components.
Explanation of the basic operational principles of the CM unit.
Detailed description of how the water level in the steam generator is controlled.
Explanation of the steam generation and control system.
Instructions for using key codes to access specific functions or modes.
Diagram and description of the CM Printed Circuit Board (PCB) and its components.
Information on the main fan motor, including LED codes and troubleshooting.
Step-by-step breakdown of operational sequences for different cooking modes.
How to access and navigate service levels for diagnostics and settings.
Overview of diagnostic modes and available tests for troubleshooting.
Displays total operating times for various unit functions and components.
Guide to configuring essential unit parameters and default settings.
Procedures for testing individual components and functions of the CM unit.
How to access and interpret recorded error codes and fault history.
Table of failure codes, their explanations, and likely causes.
Explanation of the gas system components and operational principles.
Identification and location of key gas system components.
Diagram illustrating the sequence of operations for the burner system.
Step-by-step guide for converting the unit to a different gas type.
Procedure for adjusting settings based on installation altitude above sea level.
Instructions for performing flue gas analysis and CO2 measurements.
Table providing values for burner adjustments based on gas type and settings.
Procedure for adjusting the gas blower speed for optimal performance.
Diagram showing the SCC control panel layout and its primary functions.
Description of SelfCooking Control modes for older software versions.
Details on Combi Steamer modes for older software versions.
Description of SelfCooking Control modes for newer software versions.
Details on Combi Steamer modes for newer software versions.
Instructions for programming cooking cycles and using the CleanJet function.
Wiring diagram illustrating the electrical connections of the SCC unit.
Details of the SCC operator PCB, including LED indicators and their meaning.
Information on the SCC Input/Output PCB, including LED codes and troubleshooting.
Troubleshooting guide for the SCC main fan motor based on LED codes.
Detailed sequence of events for various SCC cooking modes.
How to access and navigate the SCC service level menus.
An overview of the SCC diagnostic modes and available functions.
Detailed explanation of the SCC diagnostic mode and its features.
Overview of SCC running times for various functions and components.
Displays total operating times for various SCC unit functions.
Overview of the SCC basic settings that can be configured.
Guide to configuring essential SCC unit parameters.
Overview of the SCC function test procedures.
Step-by-step instructions for performing SCC function tests.
Overview of SCC service messages and intermittent buzzer codes.
Detailed explanations of SCC service messages and their troubleshooting.
Procedures for calibrating the SCC unit, including necessary conditions.
Diagram and description of the SCC drain valve operation.
Explanation of the gas system components and principles for SCC units.
Basic information and identification of gas burners and blowers for SCC.
Diagram illustrating the sequence of operations for the SCC burner system.
Step-by-step guide for converting the SCC unit to a different gas type.
Procedure for adjusting SCC settings based on installation altitude.
Instructions for performing flue gas analysis on SCC units.
Table of values for burner adjustments for SCC gas units.
Procedure for adjusting the gas blower speed for SCC units.
Instructions for updating the SCC unit's software via USB stick.
Troubleshooting flowchart for PCB/EEPROM issues and software updates.
General information on software updates.
Troubleshooting flowchart for CM PCB/EEPROM issues and Fault E1.
Guide for flashing CM units using a PC and Megaload software.
User instructions for the electrical descaling pump, including safety.
Checklist for installation and commissioning of SCC/CM units.
Checklist for routine preventative maintenance tasks for SCC/CM units.
Information and recommendations regarding water treatment systems for the units.
Index of fault lists for SCC and CM troubleshooting.
Detailed fault list and troubleshooting steps for SCC units.
Detailed fault list and troubleshooting steps for CM units.
Reference sheets and circuit diagrams for electrical documentation.
To Next Page
