Santec TSL-710 - Page 79

Tunable Semiconductor Laser TSL-710
7-25
Command Description Page
[:SOURce]:WAVelength:SWEep:DELay?
Reads out the wait time between each
sweep in continuous sweep operation.
7-39
[:SOURce]:WAVelength:SWEep:DWELl
Sets the amount of time spent during
each step in step sweep operation.
7-39
[:SOURce]:WAVelength:SWEep:DWELl?
Reads out the amount of time spent
during each step in step sweep
operation.
7-39
[:SOURce]:WAVelength:SWEep:MODe Sets the sweep operation mode. 7-39
[:SOURce]:WAVelength:SWEep:MODe? Reads out the sweep operation mode. 7-40
[:SOURce]:WAVelength:SWEep:SPEed Sets the speed for continuous sweep. 7-40
[:SOURce]:WAVelength:SWEep:SPEed?
Reads out the speed of continuous
sweep.
7-40
[:SOURce]:WAVelength:SWEep:STARt Sets the sweep start wavelength. 7-41
[:SOURce]:WAVelength:SWEep:STARt? Reads out the sweep start wavelength. 7-41
[:SOURce]:WAVelength:SWEep:STOP Sets the sweep end wavelength. 7-41
[:SOURce]:WAVelength:SWEep:STOP? Reads out the sweep end wavelength. 7-41
[:SOURce]:WAVelength:SWEep:STEP[:WIDTh]
Sets the step interval (wavelength) of
step sweeps.
7-42
[:SOURce]:WAVelength:SWEep:STEP[:WIDTh]?
Reads out the step interval
(wavelength) of step sweeps.
7-42
[:SOURce][:WAVelength]:FREQuency:SWEep:STARt Sets the sweep start frequency. 7-42
[:SOURce][:WAVelength]:FREQuency:SWEep:STARt? Reads out the sweep start frequency. 7-42
[:SOURce][:WAVelength]:FREQuency:SWEep:STOP Sets the sweep end frequency. 7-43
[:SOURce][:WAVelength]:FREQuency:SWEep:STOP? Reads out the sweep end frequency. 7-43
[:SOURce][:WAVelength]:FREQuency:SWEep:
STEP[:WIDTh]
Sets the step interval (frequency) of
step sweeps.
7-43
[:SOURce][:WAVelength]:FREQuency:SWEep:
STEP[:WIDTh]?
Reads out the step interval (frequency)
of step sweeps.
7-43
[:SOURce]:WAVelength:SWEep[:STATe] Sets the sweep mode state. 7-44
[:SOURce]:WAVelength:SWEep[:STATe]?
Reads out the current sweep mode
state.
7-44
[:SOURce]:WAVelength:SWEep[:STATe]:REPeat Executes a continuous sweep. 7-44
[:SOURce]:WAVelength:SWEep: SOFTtrigger Issues a soft trigger. 7-45
[:SOURce]:READout:POINts?
Reads the number of data points
recorded by wavelength logging.
7-45
[:SOURce]:READout:DATa?
Reads all the data recorded by wavelength
logging. The data is comprised of a header
(ASCII characters) and wavelength data
array (4-byte binary).
7-45
[:SOURce]:AM:STATe
Enables and disables amplitude
modulation of the laser output.
7-45
[:SOURce]:AM:STATe?
Reads out status of amplitude
modulation of the laser output.
7-46