Sanyo PLC-WU3800 Manual

PLC-WU3800 Expand Serial Command Functional Specifications
                                       
14/74
6.5 Screen Status Read Command Table
Status read command
Item
CR_SCREEN[CR]
Get selected screen size
CR_KYSTNMODE[CR]
Get setting status of Keystone Store mode
CR_VSCALE[CR]
Get setting status of Vertical Scale
CR_VPOS[CR]
Get setting status of Vertical Position
CR_HSCALE[CR]
Get setting status of Horizontal Scale
CR_HPOS[CR]
Get setting status of Horizontal Position
6.6 Lamp Status Read Command Table
Status read command
Item
CR_LAMPREPL[CR]
Get the information for Lamp replacement time
CR_LAMPH[CR]
Get lamp total running time
CR_LAMPCORRESPH
[CR]
Get corresponding lamp use time
CR_LAMPMODE[CR]
Get Lamp Mode status
CR_LAMPSTS[CR]
Get lamp lighting status
CR_PROJH[CR]
Get projector total running time
CR_HMLAMP[CR]
Get lamp number
6.7 Sound Status Read Command Table
Status read command
Item
CR_VOLUME[CR]
Get Volume value
CR_MUTE[CR]
Get Sound Mute setting status
6.8 Setting Status Read Command Table
Status read command
It
em
CR_LANG[CR]
Get selected language
CR_AUTOSETUPPCADJ
Get setting status of Auto PC in Auto setup
CR_AUTOSETUPKEYSTONE
Get setting status of Keystone in Auto setup
CR_INPUTSEARCH[CR]
Get setting status of Input search
CR_BACKGND[CR]
Get setting status screen mode for the case of no signal
CR_DISP[CR]
Get setting status of Display
CR_LOGO[CR]
Get setting status of Logo
CR_CEIL [CR]
Get setting status of Ceiling
CR_REAR[CR]
Get setting status of Rear
CR_HDMISETUP[CR]
Get status of Image mode of HDMI setup.
CR_HDMISOUND[CR]
Get status of Sound mode of HDMI setup.
CR_TERMINAL[CR]
Get setting status of Terminal.
CR_POINTER[CR]
Get setting status of Pointer
CR_STANDBYMODE[CR]
Get setting status of Standby Mode
CR_PIP[CR]
Get status of mode of Picture in Picture.
CR_PIPSIZE[CR]
Get status of Subpicture size in Picture in Picture
CR_PIPPOSITION[CR]
Get status of position of Subpicture in Picture in Picture.
CR_P
-
MANE[CR]
Get setting status of Power management
CR_P
-
MANETIME[CR]
Get setting time for Power management
CR_ON
-
STA[CR]
Get setting status of Direct on
CR_CCAPTIONDISP[CR]
Get setting status of channel of Closed caption
CR_CCAPTIONCOLOR[CR]
Get setting status of color of Closed caption
CR_RCODE[CR]
Get selected Remote Control Code
CR_S
ECURITY[CR]
Get setting status of Security
CR_KEYDIS[CR]
Get RC/KEY disability status
CR_PJLOCKNOW[CR]
Get if PJ Lock is actually in operation
CR_PJLOCKMENU[CR]
Get setting status of PJ Lock
CR_FANMODE[CR]
Get selected Fan mode
CR_FANCONTROL[CR]
Get selected Fan Control Mode

Sanyo PLC-WU3800 Specifications

General

Matrix size	0.59 \
Projection distance	0.99 - 12.1 m
Vertical scan range	50 - 100 Hz
Horizontal scan range	15 - 100 kHz
Projection technology	LCD
Contrast ratio (typical)	500:1
Screen size compatibility	40 - 300 \
Projector native resolution	WXGA (1280x800)
Keystone correction, vertical	±40 °
Audio input	2
Aspect ratio	16:10
Network ready	Yes
Power supply type	AC
Dimensions (WxDxH)	335.7 x 257.5 x 93.6 mm
Connectivity technology	Wired
Focus	Manual
Digital zoom	16 x
Focal length range	19.2 - 30.2 mm
Noise level	35 dB
Noise level (economic mode)	31 dB
Dot clock scanning frequency	140 MHz
Lamp type	NSHA
Lamp power	275 W
Light source type	Lamp
Service life of light source	2500 h
Service life of light source (economic mode)	3000 h
DVI port	No
Composite video in	-
Serial interface type	RS-232
USB 2.0 ports quantity	0
Supported video modes	1080i, 1080p, 720p
Analog signal format system	NTSC, NTSC 4.43, PAL, PAL M, PAL N, SECAM
Supported graphics resolutions	1024 x 768 (XGA), 1280 x 1024 (SXGA), 1280 x 800 (WXGA), 1400 x 1050 (SXGA+), 1600 x 1200 (UXGA), 1920 x 1200 (WUXGA), 640 x 480 (VGA), 800 x 600 (SVGA)
Product color	White
AC input voltage	100 - 240 V
Power consumption (standby)	0.7 W
Power consumption (typical)	317 W
Power consumption (PowerSave)	280 W
Cables included	VGA

Weight and Dimensions

Depth	257.5 mm
Width	335.7 mm
Height	93.6 mm
Weight	3500 g