Sanyo PLC-WU3800 Manual

PLC-WU3800 Expand Serial Command Functional Specifications
                                       
64/74
9.11 Setting Status Read Command
9.11.1 CR_LANG Command
Command “CR_LANG”[CR]
Details Get selected language
Response
Acceptable “000_%a”[CR]
%a
“ENG” -------------------------- English is selected
“DEU” -------------------------- German is selected
“FRA” -------------------------- French is selected
“ITA” --------------------------- Italian is selected
“ESP” -------------------------- Spanish is selected
“POR” -------------------------- Portuguese is selected
“NED” -------------------------- Dutch is selected
“SVE” -------------------------- Swedish is selected
“RUS” -------------------------- Russian is selected
“CHI” -------------------------- Chinese is selected
“KOR” -------------------------- Korean is selected
“JPN” -------------------------- Japanese is selected
“FIN” ---------------------------- Finnish is selected
“POL” --------------------------- Polish is selected
“HUN” -------------------------- Hungarian is selected
“ROM” -------------------------- Romanian is selected
“THA” --------------------------- Thai is selected
Unacceptable “Error code”[CR]
9.11.2 CR_AUTOSETUPPCADJ Command
Command “CR_AUTOSETUPPCADJ” [CR]
Details Get Auto PC adj. setting status in Auto setup
Response
Acceptable “000_%a”[CR]
%a
“ON” ------------------ Auto PC ADJ. in Auto setup is ON
“OFF” ----------------- Auto PC ADJ. in Auto setup is OFF
Unacceptable “Error code”[CR]
9.11.3 CR_AUTOSETUPKEYSTONE Command
Command “CR_AUTOSETUPKEYSTONE” [CR]
Details Get Keystone setting status in Auto setup
Response
Acceptable “000_%a”[CR]
%a
“AUTO” -------------- Auto Keystone is Auto
“MANUAL” ---------- Auto Keystone is Manual
“OFF” ---------------- Auto Keystone is OFF
Unacceptable “Error code”[CR]
9.11.4 CR_INPUTSEARCH Command
Command “CR_INPUTSEARCH”[CR]
Details Get setting status of Input search
Response
Acceptable “000_%a”[CR]
%a
“OFF” --------------------- Input search is OFF
“ON1” --------------------- Input search is On1
“ON2” --------------------- Input search is On2
Unacceptable “Error Code”[CR]

Sanyo PLC-WU3800 Specifications

General

Matrix size	0.59 \
Projection distance	0.99 - 12.1 m
Vertical scan range	50 - 100 Hz
Horizontal scan range	15 - 100 kHz
Projection technology	LCD
Contrast ratio (typical)	500:1
Screen size compatibility	40 - 300 \
Projector native resolution	WXGA (1280x800)
Keystone correction, vertical	±40 °
Audio input	2
Aspect ratio	16:10
Network ready	Yes
Power supply type	AC
Dimensions (WxDxH)	335.7 x 257.5 x 93.6 mm
Connectivity technology	Wired
Focus	Manual
Digital zoom	16 x
Focal length range	19.2 - 30.2 mm
Noise level	35 dB
Noise level (economic mode)	31 dB
Dot clock scanning frequency	140 MHz
Lamp type	NSHA
Lamp power	275 W
Light source type	Lamp
Service life of light source	2500 h
Service life of light source (economic mode)	3000 h
DVI port	No
Composite video in	-
Serial interface type	RS-232
USB 2.0 ports quantity	0
Supported video modes	1080i, 1080p, 720p
Analog signal format system	NTSC, NTSC 4.43, PAL, PAL M, PAL N, SECAM
Supported graphics resolutions	1024 x 768 (XGA), 1280 x 1024 (SXGA), 1280 x 800 (WXGA), 1400 x 1050 (SXGA+), 1600 x 1200 (UXGA), 1920 x 1200 (WUXGA), 640 x 480 (VGA), 800 x 600 (SVGA)
Product color	White
AC input voltage	100 - 240 V
Power consumption (standby)	0.7 W
Power consumption (typical)	317 W
Power consumption (PowerSave)	280 W
Cables included	VGA

Weight and Dimensions

Depth	257.5 mm
Width	335.7 mm
Height	93.6 mm
Weight	3500 g