EasyManuals Logo

Sanyo PLC-WU3800 Manual

Sanyo PLC-WU3800
74 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #18 background imageLoading...
Page #18 background image
PLC-WU3800 Expand Serial Command Functional Specifications
18/74
8.4 Image Command
8.4.1 CF_BRIGHT Command
Command
"CF_BRIGHT_%1”[CR]
%1
"000~063” --------------- Directly select Brightness setting value
"UP” ----------------------- Current Brightness setting value + 1
"DN ----------------------- Current Brightness setting value – 1
Details
Set Brightness value of user control
The value set by this command will not be saved to projector. Therefore, when
turning into Standby mode or ALL is OFF, the value returns to original setting. (The
value is held in Suspend mode.)
This command is available in normal Power ON status.
Response
Acceptable “000”[CR]
Unacceptable
“Error Code[CR]
8.4.2 CF_CONT Command
Command
“CF_CONT_1”[CR]
%1
“000~063” --------------- Directly select Contrast setting value
“UP” ----------------------- Current Contrast setting value + 1
“DN” ----------------------- Current Contrast setting value – 1
Details
Set Contrast value of user control
The value set by this command will not be saved to projector. Therefore, when
turning into Standby-mode or ALL is OFF, the value returns to original setting. (The
value is held in Suspend mode.)
This command is available in normal Power ON status.
Response
Acceptable “000”[CR]
Unacceptable
"Error Code”[CR]
8.4.3 CF_COLOR Command
Command
“CF_COLOR_%1”[CR]
%1
“000~063” ---------------- Directly select Color setting value
“UP” ------------------------ Current Color setting value + 1
“DN” ------------------------ Current Color setting value - 1
Details
Set Color value of user control
The value set by this command will not be saved to projector. Therefore, when
turning into Standby-mode or ALL is OFF, the value returns to original setting. (The
value is held in Suspend mode.)
This command is available in normal Power ON status.
Response
Acceptable “000”[CR]
Unacceptable
“Error Code[CR]
8.4.4 CF_TINT Command
Command
“CF_TINT_%1”[CR]
%1
“000~063” --------------- Directly select Tint setting value
“UP” ----------------------- Current Tint setting value + 1
“DN” ----------------------- Current Tint setting value – 1
Details
Set Tint value of user control
The value set by this command will not be saved to projector. Therefore, when
turning into Standby-mode or ALL is OFF, the value returns to original setting. (The
value is held in Suspend mode.)
This command is available in normal Power ON status.
Response
Acceptable “000”[CR]
Unacceptable
“Error Code[CR]

Table of Contents

Other manuals for Sanyo PLC-WU3800

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Sanyo PLC-WU3800 and is the answer not in the manual?

Sanyo PLC-WU3800 Specifications

General IconGeneral
Matrix size0.59 \
Projection distance0.99 - 12.1 m
Vertical scan range50 - 100 Hz
Horizontal scan range15 - 100 kHz
Projection technologyLCD
Contrast ratio (typical)500:1
Screen size compatibility40 - 300 \
Projector native resolutionWXGA (1280x800)
Keystone correction, vertical±40 °
Audio input2
Aspect ratio16:10
Network readyYes
Power supply typeAC
Dimensions (WxDxH)335.7 x 257.5 x 93.6 mm
Connectivity technologyWired
FocusManual
Digital zoom16 x
Focal length range19.2 - 30.2 mm
Noise level35 dB
Noise level (economic mode)31 dB
Dot clock scanning frequency140 MHz
Lamp typeNSHA
Lamp power275 W
Light source typeLamp
Service life of light source2500 h
Service life of light source (economic mode)3000 h
DVI portNo
Composite video in-
Serial interface typeRS-232
USB 2.0 ports quantity0
Supported video modes1080i, 1080p, 720p
Analog signal format systemNTSC, NTSC 4.43, PAL, PAL M, PAL N, SECAM
Supported graphics resolutions1024 x 768 (XGA), 1280 x 1024 (SXGA), 1280 x 800 (WXGA), 1400 x 1050 (SXGA+), 1600 x 1200 (UXGA), 1920 x 1200 (WUXGA), 640 x 480 (VGA), 800 x 600 (SVGA)
Product colorWhite
AC input voltage100 - 240 V
Power consumption (standby)0.7 W
Power consumption (typical)317 W
Power consumption (PowerSave)280 W
Cables includedVGA
Weight and Dimensions IconWeight and Dimensions
Depth257.5 mm
Width335.7 mm
Height93.6 mm
Weight3500 g

Related product manuals