Sanyo PLC-WU3800 Manual

PLC-WU3800 Expand Serial Command Functional Specifications
                                       
29/74
8.6.9 CF_SYSTEM Command
Command “CF_SYSTEM_%1”[CR]
%1
Input is
Computer
“VGA1” ------------- Select VGA1
:
“XGA1” ------------- Select XGA1
:
“WXGA3” ------------ Select WXGA3
“1080I” --------------- Select 1080I
“1035I” --------------- Select 1035I
“720P” ---------------- Select 720P
”575P” ---------------- Select 575P
”480P” ---------------- Select 480P
”575I” ----------------- Select 575I
”480I” ----------------- Select 480I
“MODE1”~ “MODE5”------------- Select Mode 1~Mode 5
Input is HDMI
”D-XGA1” --------------- Select D-XGA1
:
:
”D-WXGA3” ------------- Select D-WXGA3
”D-1080I” ---------------- Select D-1080I
”D-1035I” ---------------- Select D-1035I
”D-720P” ---------------- Select D-720P
”D-575P” ---------------- Select D-575P
”D-480P” ---------------- Select D-480P
Projector returns “101” when no signal is detected.
Input is
Video
“AUTO” -------------------------- Select System “Auto”
“NTSC” -------------------------- Select NTSC
“NTSC443” --------------------- Select NTSC4.43
“PAL” ----------------------------- Select PAL
“SECAM” ----------------------- Select SECAM
“PAL-M” ------------------------- Select PAL-M
“PAL-N” ------------------------- Select PAL-N
“1080I” -------------------------- Select 1080i
“1035I” -------------------------- Select 1035i
“720P” --------------------------- Select 720p
“575P” --------------------------- Select 575p
“480P” --------------------------- Select 480p
“575I” ---------------------------- Select 575i
“480I” ---------------------------- Select 480i
Details
Select System of currently selected Input
When Input specified by %1 is inappropriate for selected Input, the projector
returns “101”[CR] and the command is not executed
This command is available in normal Power ON status.
Note1) “NTSC” / ”NTSC4.43” / ”PAL” / ”SECAM” / ”PAL-M” / ”PAL-N” is available
only when Input is VIDEO / S-VIDEO
Note2) “1080I” / ”1035I” / ”720P” / ”575P” / ”480P” / “575I” / “480I” is available only
when Input is Y / Pb/Cb / Pr/Cr
Note3) D-XGA1/…/D-480P is available only when Input is applicable.
Response
Acceptable “000”[CR]
Unacceptable “Error Code”[CR]

Sanyo PLC-WU3800 Specifications

General

Matrix size	0.59 \
Projection distance	0.99 - 12.1 m
Vertical scan range	50 - 100 Hz
Horizontal scan range	15 - 100 kHz
Projection technology	LCD
Contrast ratio (typical)	500:1
Screen size compatibility	40 - 300 \
Projector native resolution	WXGA (1280x800)
Keystone correction, vertical	±40 °
Audio input	2
Aspect ratio	16:10
Network ready	Yes
Power supply type	AC
Dimensions (WxDxH)	335.7 x 257.5 x 93.6 mm
Connectivity technology	Wired
Focus	Manual
Digital zoom	16 x
Focal length range	19.2 - 30.2 mm
Noise level	35 dB
Noise level (economic mode)	31 dB
Dot clock scanning frequency	140 MHz
Lamp type	NSHA
Lamp power	275 W
Light source type	Lamp
Service life of light source	2500 h
Service life of light source (economic mode)	3000 h
DVI port	No
Composite video in	-
Serial interface type	RS-232
USB 2.0 ports quantity	0
Supported video modes	1080i, 1080p, 720p
Analog signal format system	NTSC, NTSC 4.43, PAL, PAL M, PAL N, SECAM
Supported graphics resolutions	1024 x 768 (XGA), 1280 x 1024 (SXGA), 1280 x 800 (WXGA), 1400 x 1050 (SXGA+), 1600 x 1200 (UXGA), 1920 x 1200 (WUXGA), 640 x 480 (VGA), 800 x 600 (SVGA)
Product color	White
AC input voltage	100 - 240 V
Power consumption (standby)	0.7 W
Power consumption (typical)	317 W
Power consumption (PowerSave)	280 W
Cables included	VGA

Weight and Dimensions

Depth	257.5 mm
Width	335.7 mm
Height	93.6 mm
Weight	3500 g