EasyManuals Logo

Sanyo PLC-WU3800 Manual

Sanyo PLC-WU3800
74 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #43 background imageLoading...
Page #43 background image
PLC-WU3800 Expand Serial Command Functional Specifications
43/74
8.10.23 CF_CCAPTIONCOLOR Command
Command
“CF_CCAPTIONCOLOR_%1”[CR]
%1
“COLOR” ------- Select Color
“WHITE” -------- Select White
Details
Select color of Closed caption.
The status set with this command is stored in EEPROM and its setting is effective
even after ALL is OFF.
This command is available in normal Power ON status.
Note)Closed caption is available under conditions below;
Entered signal is appropriate (Video, NTSC signal of S-video, Component=480i)
and System is fixed to NTSC or 480i.
Response
Acceptable “000”[CR]
Unacceptable
“Error Code[CR]
8.10.24 CF_RCODE Command
Command
“CF_RCODE_%1”[CR]
%1
"001” --------------------------- Select Code1
"002” --------------------------- Select Code2
“UP” --------------- Switch Code setting of Remote Control forward
(Code1 Code2 Code3 ・・ Code8 Code1)
“DN” --------------- Switch Code setting of Remote Control backward
(Code8 Code7 Code6 ・・ Code1 Code8)
Details
Select Code of Remote Control
The status set by this command is stored in EEPROM and its setting is effective
after ALL is OFF
This command is available in normal Power ON status.
Response
Acceptable “000”[CR]
Unacceptable
“Error Code[CR]
8.10.25 CF_KEYDIS Command
Command
“CF_KEYDIS_%1”[CR]
%1
“NONE ----------------------- RC & Projector keys are valid (All are valid)
“RC” ---------------------------- RC keys are invalid
“KEY” -------------------------- Projector keys are invalid
Details
Disable RC/Projector keys
This command is available in normal Power ON status.
Response
Acceptable “000”[CR]
Unacceptable
“Error Code[CR]

Table of Contents

Other manuals for Sanyo PLC-WU3800

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Sanyo PLC-WU3800 and is the answer not in the manual?

Sanyo PLC-WU3800 Specifications

General IconGeneral
Matrix size0.59 \
Projection distance0.99 - 12.1 m
Vertical scan range50 - 100 Hz
Horizontal scan range15 - 100 kHz
Projection technologyLCD
Contrast ratio (typical)500:1
Screen size compatibility40 - 300 \
Projector native resolutionWXGA (1280x800)
Keystone correction, vertical±40 °
Audio input2
Aspect ratio16:10
Network readyYes
Power supply typeAC
Dimensions (WxDxH)335.7 x 257.5 x 93.6 mm
Connectivity technologyWired
FocusManual
Digital zoom16 x
Focal length range19.2 - 30.2 mm
Noise level35 dB
Noise level (economic mode)31 dB
Dot clock scanning frequency140 MHz
Lamp typeNSHA
Lamp power275 W
Light source typeLamp
Service life of light source2500 h
Service life of light source (economic mode)3000 h
DVI portNo
Composite video in-
Serial interface typeRS-232
USB 2.0 ports quantity0
Supported video modes1080i, 1080p, 720p
Analog signal format systemNTSC, NTSC 4.43, PAL, PAL M, PAL N, SECAM
Supported graphics resolutions1024 x 768 (XGA), 1280 x 1024 (SXGA), 1280 x 800 (WXGA), 1400 x 1050 (SXGA+), 1600 x 1200 (UXGA), 1920 x 1200 (WUXGA), 640 x 480 (VGA), 800 x 600 (SVGA)
Product colorWhite
AC input voltage100 - 240 V
Power consumption (standby)0.7 W
Power consumption (typical)317 W
Power consumption (PowerSave)280 W
Cables includedVGA
Weight and Dimensions IconWeight and Dimensions
Depth257.5 mm
Width335.7 mm
Height93.6 mm
Weight3500 g

Related product manuals