EasyManuals Logo

Sanyo PLC-WU3800 Manual

Sanyo PLC-WU3800
74 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #69 background imageLoading...
Page #69 background image
PLC-WU3800 Expand Serial Command Functional Specifications
69/74
%1
“LOCK” ------------- PJ Lock is in operation. PJ Lock status is ON-1
or ON-2 on Menu, and PJ PIN CODE is not
entered so that projector is actually locked.
“FREE” ------------- PJ Lock is released. PJ Lock status is OFF, or,
status is ON-1 or ON-2 on Menu but PJ PIN
CODE is entered correctly so that PJ Lock is
released.
Unacceptable
“Error Code [CR]
9.11.26 CR_PJLOCKMENU Command
Command
“CR_PJLOCKMENU” [CR]
Details Get status of PJ Lock on Menu
Response
Acceptable “000_%1[CR]
%1
“ON1” ------------- PJ Lock status is On-1
“ON2” ------------- PJ Lock status is On-2
“OFF” ------------- PJ Lock status is OFF
Unacceptable
“Error Code [CR]
9.11.27 CR_FANMODE Command
Command
“CR_FANMODE”[CR]
Details Get selected Fan mode
Response
Acceptable “000_%a”[CR]
%a
“L1” ----------------------- Fan mode is L1
“L2” ----------------------- Fan mode is L2
Unacceptable
“Error code”[CR]
9.11.28 CR_FANCONTROL Command
Command
“CR_FANCONTROL”[CR]
Details Get selected Fan control setting status
Response
Acceptable “000_%a”[CR]
%a
“OFF” ----------------------- Fan control is OFF
“ON1” ----------------------- Fan control is ON1
“ON2” ----------------------- Fan control is ON2
“ON3” ----------------------- Fan control is ON3
Unacceptable
“Error code”[CR]
9.11.29 CR_FILH Command
Command
“CR_FILH”[CR]
Details Get Filter used time
Response
Acceptable “000_%1”[CR]
%1 “00000”~”99999” ------------------- 0 hour to 99999 hours
Unacceptable
Error Code”[CR]
9.11.30 CR_FILREPL Command
Command
“CR_FILREPL”[CR]
Details Get the information of Filter replacement time
Response
Acceptable “000_%1”[CR]

Table of Contents

Other manuals for Sanyo PLC-WU3800

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Sanyo PLC-WU3800 and is the answer not in the manual?

Sanyo PLC-WU3800 Specifications

General IconGeneral
Matrix size0.59 \
Projection distance0.99 - 12.1 m
Vertical scan range50 - 100 Hz
Horizontal scan range15 - 100 kHz
Projection technologyLCD
Contrast ratio (typical)500:1
Screen size compatibility40 - 300 \
Projector native resolutionWXGA (1280x800)
Keystone correction, vertical±40 °
Audio input2
Aspect ratio16:10
Network readyYes
Power supply typeAC
Dimensions (WxDxH)335.7 x 257.5 x 93.6 mm
Connectivity technologyWired
FocusManual
Digital zoom16 x
Focal length range19.2 - 30.2 mm
Noise level35 dB
Noise level (economic mode)31 dB
Dot clock scanning frequency140 MHz
Lamp typeNSHA
Lamp power275 W
Light source typeLamp
Service life of light source2500 h
Service life of light source (economic mode)3000 h
DVI portNo
Composite video in-
Serial interface typeRS-232
USB 2.0 ports quantity0
Supported video modes1080i, 1080p, 720p
Analog signal format systemNTSC, NTSC 4.43, PAL, PAL M, PAL N, SECAM
Supported graphics resolutions1024 x 768 (XGA), 1280 x 1024 (SXGA), 1280 x 800 (WXGA), 1400 x 1050 (SXGA+), 1600 x 1200 (UXGA), 1920 x 1200 (WUXGA), 640 x 480 (VGA), 800 x 600 (SVGA)
Product colorWhite
AC input voltage100 - 240 V
Power consumption (standby)0.7 W
Power consumption (typical)317 W
Power consumption (PowerSave)280 W
Cables includedVGA
Weight and Dimensions IconWeight and Dimensions
Depth257.5 mm
Width335.7 mm
Height93.6 mm
Weight3500 g

Related product manuals