Sanyo PLC-WU3800 Manual

PLC-WU3800 Expand Serial Command Functional Specifications
                                       
57/74
9.7.9 CR_SYSTEM Command
Command “CR_SYSTEM”[CR]
Details Get selected System
Response
Acceptable “000_%1”[CR]
%1
Input is
PC Analog
“VGA1” -------------- VGA1 is selected
“VGA2” -------------- VGA2 is selected
  ：
“XGA1”-------------- XGA1 is selected
  ：
“WXGA3” --------- WXGA3 is selected
“1080I” ------------ 1080i is selected
“1035I” ------------ 1035i is selected
“720P” ------------- 720p is selected
“575P” ------------- 575p is selected
“480P” ------------- 480p is selected
“575I” -------------- 575i is selected
“480I” -------------- 480i is selected
“MODE1” ------- Mode1 is selected
  ：
“MODE5” -------------- Mode5 is selected
When there is no signal, projector returns error code”101”
[CR]
Input is
HDMI
“D−XGA1” ------------- D-XGA1 is selected
  ：
“D−WXGA3” ---------- D-WXGA3 is selected
“D−1080I” ------------- D-1080i is selected
“D−1035I” ------------- D-1035i is selected
“D−720P” ------------- D-720p is selected
“D−575P” ------------- D-575p is selected
“D−480P” ------------- D-480p is selected
When there is no signal, projector returns error code”101”
[CR]
Input is
Y,Pb/Cb,Pr
/Cr
“AUTO” ----------- Auto is selected
“1080I” ------------1080i is selected
“1035I” ------------ 1035i is selected
“720P” ------------- 720p is selected
“575P” ------------- 575p is selected
“480P” ------------- 480p is selected
“575I” -------------- 575i is selected
“480I” -------------- 480i is selected
Projector returns selected System status regardless of the
signal input.
Input is
Video,S-Vi
deo
“AUTO” --------------- Auto is selected
“NTSC” --------------- NTSC is selected
“NTSC443” ---------- NTSC4.43 is selected
“PAL” ------------------ PAL is selected
“SECAM” ------------- SECAM is selected
“PAL−M” ------------- PAL-M is selected
“PAL−N” ------------- AL-N is selected
Projector returns selected System status regardless of the
signal input.
Input is
Network
“NETWORK” --------------- Network is selected
Projector returns selected System status regardless of the
signal input.
Unacceptable ““Error Code”[CR]

Sanyo PLC-WU3800 Specifications

General

Matrix size	0.59 \
Projection distance	0.99 - 12.1 m
Vertical scan range	50 - 100 Hz
Horizontal scan range	15 - 100 kHz
Projection technology	LCD
Contrast ratio (typical)	500:1
Screen size compatibility	40 - 300 \
Projector native resolution	WXGA (1280x800)
Keystone correction, vertical	±40 °
Audio input	2
Aspect ratio	16:10
Network ready	Yes
Power supply type	AC
Dimensions (WxDxH)	335.7 x 257.5 x 93.6 mm
Connectivity technology	Wired
Focus	Manual
Digital zoom	16 x
Focal length range	19.2 - 30.2 mm
Noise level	35 dB
Noise level (economic mode)	31 dB
Dot clock scanning frequency	140 MHz
Lamp type	NSHA
Lamp power	275 W
Light source type	Lamp
Service life of light source	2500 h
Service life of light source (economic mode)	3000 h
DVI port	No
Composite video in	-
Serial interface type	RS-232
USB 2.0 ports quantity	0
Supported video modes	1080i, 1080p, 720p
Analog signal format system	NTSC, NTSC 4.43, PAL, PAL M, PAL N, SECAM
Supported graphics resolutions	1024 x 768 (XGA), 1280 x 1024 (SXGA), 1280 x 800 (WXGA), 1400 x 1050 (SXGA+), 1600 x 1200 (UXGA), 1920 x 1200 (WUXGA), 640 x 480 (VGA), 800 x 600 (SVGA)
Product color	White
AC input voltage	100 - 240 V
Power consumption (standby)	0.7 W
Power consumption (typical)	317 W
Power consumption (PowerSave)	280 W
Cables included	VGA

Weight and Dimensions

Depth	257.5 mm
Width	335.7 mm
Height	93.6 mm
Weight	3500 g