EasyManuals Logo

Sanyo PLC-WU3800 Manual

Sanyo PLC-WU3800
74 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #73 background imageLoading...
Page #73 background image
PLC-WU3800 Expand Serial Command Functional Specifications
73/74
9.12.7 CR_TEMP Command
Command
"CR_TEMP”[CR]
Details
Get current temperature inside a projector.
If there are several sensors installed, it is possible to get information from all the
sensors at once.
Response
Acceptable “000_%1_%2_%3”[CR]
%1,%2,%3
%1= Sensor 1 temperature (Outside temperature)
%2= Sensor 2 temperature (Inside temperature1)
%3= Sensor 3 temperature (Inside temperature2)
%1,%2 are consists of 6 bites fixed
There must be 1 space between %1 and %2, and, %2 and %3
e.g. _31.5F
“_” means a space and “_” changes into “-“, when temperature
gets below freezing.
e.g. -05.5F
The last character shows if corresponding sensor is under
abnormal temperature.
“F” ------- Abnormal temperature
“W”-------Close to abnormal temperature(Temperature is as
high
to display Warning)
“S” -------Not close to abnormal temperature (Temperature is low
enough and safe.)
“N”-------Applicable sensor does not detect abnormal temperature
“E” -------Not able to return temperature data
When several sensors are incorporated, projector returns values
continuously.
e.g. “_31.5F__35.2S__38.0W”[CR]
A data of sensor 1 comes first and a data of sensor 2 follows
after
1 space.
As described respectively in e.g., sensor 1 detects abnormal
temp., sensor 2 detects 35.2 degrees which means safety, and
sensor 3 is 38 degrees which is close to abnormal temp.
In case projector cannot return its data due to some hard ware
failure, the last character becomes “E” such as “_00.0E”.
Some of the projectors get abnormal temperature because of
heat of Lamp ballast in Standby mode or Powering ON.
Therefore detection of abnormal temperature is suspended while
Standby mode or adequate time after Power ON, and during that
time projector returns “_----N” as a temperature data.
Unacceptable
“Error Code[CR]

Table of Contents

Other manuals for Sanyo PLC-WU3800

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Sanyo PLC-WU3800 and is the answer not in the manual?

Sanyo PLC-WU3800 Specifications

General IconGeneral
Matrix size0.59 \
Projection distance0.99 - 12.1 m
Vertical scan range50 - 100 Hz
Horizontal scan range15 - 100 kHz
Projection technologyLCD
Contrast ratio (typical)500:1
Screen size compatibility40 - 300 \
Projector native resolutionWXGA (1280x800)
Keystone correction, vertical±40 °
Audio input2
Aspect ratio16:10
Network readyYes
Power supply typeAC
Dimensions (WxDxH)335.7 x 257.5 x 93.6 mm
Connectivity technologyWired
FocusManual
Digital zoom16 x
Focal length range19.2 - 30.2 mm
Noise level35 dB
Noise level (economic mode)31 dB
Dot clock scanning frequency140 MHz
Lamp typeNSHA
Lamp power275 W
Light source typeLamp
Service life of light source2500 h
Service life of light source (economic mode)3000 h
DVI portNo
Composite video in-
Serial interface typeRS-232
USB 2.0 ports quantity0
Supported video modes1080i, 1080p, 720p
Analog signal format systemNTSC, NTSC 4.43, PAL, PAL M, PAL N, SECAM
Supported graphics resolutions1024 x 768 (XGA), 1280 x 1024 (SXGA), 1280 x 800 (WXGA), 1400 x 1050 (SXGA+), 1600 x 1200 (UXGA), 1920 x 1200 (WUXGA), 640 x 480 (VGA), 800 x 600 (SVGA)
Product colorWhite
AC input voltage100 - 240 V
Power consumption (standby)0.7 W
Power consumption (typical)317 W
Power consumption (PowerSave)280 W
Cables includedVGA
Weight and Dimensions IconWeight and Dimensions
Depth257.5 mm
Width335.7 mm
Height93.6 mm
Weight3500 g

Related product manuals