EasyManuals Logo

Sanyo PLC-WU3800 Manual

Sanyo PLC-WU3800
74 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #30 background imageLoading...
Page #30 background image
PLC-WU3800 Expand Serial Command Functional Specifications
30/74
8.7 Screen Control Command
8.7.1 CF_SCREEN Command
Command
“CF_SCREEN_%1”[CR]
%1
Input is
Computer
“NORMAL” --------------------- Select Normal size
“TRUE” -------------------------- Select True size
“FULL” --------------------------- Select Full screen size
“CUSTOM” --------------------- Select Custom size
“DZOOM_UP” ---------------- Expand image size with Digital Zoom
“DZOOM_DN” ---------------- Reduce image size with Digital Zoom
“UP” ------------------------ Switch selectable screen size forward
(Normal True Full Custom Normal)
“DN” ------------------------ Switch selectable screen size backward
(Normal Custom Full True Normal)
Input is
Video
“NORMAL” ---------------------- Select Normal mode
“ZOOM” --------------------------- Select Zoom mode
“NATURAL” ---------------------- Select Natural wide mode
“FULL” --------------------------- Select Full mode
“CUSTOM” ---------------------- Select Custom size
“UP” ------------------------ Switch selectable screen size forward
(Normal Full Zoom Wide Natural Custom
Normal…)
“DN” ------------------------ Switch selectable screen size backward
(Custom Natural Wide Zoom Full Normal
Custom…)
Details
Select image size on screen.
When Input specified by %1 is inappropriate for selected Input, the projector
returns “101” [CR] and the command is not executed.
“DZOOM UP” and “DZOOM DN” start effecting from the first command.
This command is available in normal Power ON status.
Note) When Input is computer and AV sorts signals (480i / 575i…etc) are entered,
the signal recognized as Video Input.
Response
Acceptable “000”[CR]
Unacceptable
“Error Code[CR]
8.7.2 CF_DZCENT Command
Command
“CF_DZCENT_%1”[CR]
%1 ”CENT” ---- Cancel Digital Zoom (CENT: “CENTER”)
Details
Cancel Digital Zoom
When image is expanded or shrunk, reset its value.
This command is available in normal Power ON status and when Input is
Computer.
Response
Acceptable “000”[CR]
Unacceptable
“101”[CR] ------ when Input for Video is selected

Table of Contents

Other manuals for Sanyo PLC-WU3800

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Sanyo PLC-WU3800 and is the answer not in the manual?

Sanyo PLC-WU3800 Specifications

General IconGeneral
Matrix size0.59 \
Projection distance0.99 - 12.1 m
Vertical scan range50 - 100 Hz
Horizontal scan range15 - 100 kHz
Projection technologyLCD
Contrast ratio (typical)500:1
Screen size compatibility40 - 300 \
Projector native resolutionWXGA (1280x800)
Keystone correction, vertical±40 °
Audio input2
Aspect ratio16:10
Network readyYes
Power supply typeAC
Dimensions (WxDxH)335.7 x 257.5 x 93.6 mm
Connectivity technologyWired
FocusManual
Digital zoom16 x
Focal length range19.2 - 30.2 mm
Noise level35 dB
Noise level (economic mode)31 dB
Dot clock scanning frequency140 MHz
Lamp typeNSHA
Lamp power275 W
Light source typeLamp
Service life of light source2500 h
Service life of light source (economic mode)3000 h
DVI portNo
Composite video in-
Serial interface typeRS-232
USB 2.0 ports quantity0
Supported video modes1080i, 1080p, 720p
Analog signal format systemNTSC, NTSC 4.43, PAL, PAL M, PAL N, SECAM
Supported graphics resolutions1024 x 768 (XGA), 1280 x 1024 (SXGA), 1280 x 800 (WXGA), 1400 x 1050 (SXGA+), 1600 x 1200 (UXGA), 1920 x 1200 (WUXGA), 640 x 480 (VGA), 800 x 600 (SVGA)
Product colorWhite
AC input voltage100 - 240 V
Power consumption (standby)0.7 W
Power consumption (typical)317 W
Power consumption (PowerSave)280 W
Cables includedVGA
Weight and Dimensions IconWeight and Dimensions
Depth257.5 mm
Width335.7 mm
Height93.6 mm
Weight3500 g

Related product manuals