Schenck process Intecont Tersus Beltweigher User Manual

Table of Contents
INTECONT® Tersus Belt weigher, Instruction Manual
Schenck Process Group
BV-H2464GB, 1234
- i -
Table of Contents
Table of ContentsTable of Contents
Table of Contents
1
11
1
About This Manual
About This ManualAbout This Manual
About This Manual
................................
................................................................
................................
................................
................................................................
................................
................................
................................................................
................................
................................
................................................................
................................
1
11
1
2
22
2
Safety notes
Safety notesSafety notes
Safety notes
................................
................................................................
................................
................................
................................................................
................................
................................
................................................................
................................
................................
................................................................
................................
..........
....................
..........
3
33
3
2.1
Signal Words
................................
................................
................................
................................
.........
4
2.1.1
Signal Words for Safety Warnings
................................
................................
................................
4
2.1.2
Signal Words for Application Notes
................................
................................
..............................
5
2.2
Five Safety Rules of Electrical Engineering
................................
................................
..........................
5
2.3
Damaged / Defective Electrical Components
................................
................................
........................
6
3
33
3
General Diagram
General DiagramGeneral Diagram
General Diagram
................................
................................................................
................................
................................
................................................................
................................
................................
................................................................
................................
................................
................................................................
................................
..
....
..
7
77
7
3.1
An overview of the INTECONT Tersus
................................
................................
................................
.
7
3.2
Diagram of beltweigher and weighfeeder
................................
................................
..............................
7
3.3
Method of Function
................................
................................
................................
................................
8
3.4
Characteristics
................................
................................
................................
................................
.......
9
4
44
4
Operation
OperationOperation
Operation
................................
................................................................
................................
................................
................................................................
................................
................................
................................................................
................................
................................
................................................................
................................
............
........................
............
15
1515
15
4.1
Quick guide
................................
................................
................................
................................
.........
15
4.2
Function block
................................
................................
................................
................................
.....
17
4.3
Operating in Normal Operation
................................
................................
................................
...........
18
5
55
5
Service Functions
Service FunctionsService Functions
Service Functions
................................
................................................................
................................
................................
................................................................
................................
................................
................................................................
................................
...............................
..............................................................
...............................
21
2121
21
5.1
Display Test and Version Number
................................
................................
................................
......
21
6
66
6
Counter functions
Counter functionsCounter functions
Counter functions
................................
................................................................
................................
................................
................................................................
................................
................................
................................................................
................................
................................
................................................................
................................
23
2323
23
7
77
7
Mode functions
Mode functionsMode functions
Mode functions
................................
................................................................
................................
................................
................................................................
................................
................................
................................................................
................................
................................
................................................................
................................
...
......
...
25
2525
25
7.1
Keyboard operation ON/OFF
................................
................................
................................
..............
25
7.2
Prefeeder
................................
................................
................................
................................
............
25
7.3
Simulation
................................
................................
................................
................................
...........
25
8
88
8
Calibration functions
Calibration functionsCalibration functions
Calibration functions
................................
................................................................
................................
................................
................................................................
................................
................................
................................................................
................................
...........................
......................................................
...........................
27
2727
27
8.1
Starting the calibration functions
................................
................................
................................
........
27
8.2
Pulse/Belt circuit LB
................................
................................
................................
...........................
27
8.3
Tare TW
................................
................................
................................
................................
..............
29
8.4
Weight Check CW
................................
................................
................................
..............................
30
8.5
Setting the Time
................................
................................
................................
................................
.
32
9
99
9
Parameter functions
Parameter functionsParameter functions
Parameter functions
................................
................................................................
................................
................................
................................................................
................................
................................
................................................................
................................
............................
........................................................
............................
33
3333
33
9.1
Read Parameters
................................
................................
................................
..............................
33
10
1010
10
Printer functions
Printer functionsPrinter functions
Printer functions
................................
................................................................
................................
................................
................................................................
................................
................................
................................................................
................................
................................
................................................................
................................
..
....
..
35
3535
35
10.1
Status Report
................................
................................
................................
................................
......
35
11
1111
11
Batching functions
Batching functionsBatching functions
Batching functions
................................
................................................................
................................
................................
................................................................
................................
................................
................................................................
................................
..............................
............................................................
..............................
37
3737
37
11.1
Batching mode
................................
................................
................................
................................
....
37
11.2
Record the batch
................................
................................
................................
................................
39

Schenck process Intecont Tersus Beltweigher Specifications

General

Brand	Schenck process
Model	Intecont Tersus Beltweigher
Category	Control Panel
Language	English