MX-2300/2700 N/G SIMULATION 7 – 12
3-10
Purpose : Adjustment
Function (Purpose) : Used to adjust the finisher.
Section : Finisher
Item : Operation
Operation/Procedure
1) Select the item according to the adjustment content with [↑] [↓]
buttons.
2) Enter the adjustment value with 10-key.
3) Press [OK] button. (The set value is saved.)
<Saddle finisher>
<Inner finisher>
[Screen (Saddle finisher installed)]
4
4-2
Purpose : Operation test/check
Function (Purpose) : Used to check the operations of the sen-
sors and detectors in the desk/large capac-
ity tray and the related circuit.
Section : Desk/Large capacity tray (LCC)
Item : Operation
Operation/Procedure
The active sensors and detectors are highlighted.
The active sensors and detectors are highlighted.
<Desk sensor>
<A4 LCC sensor>
Item Display Item
Set
range
Default
value
A SADDLE POSITOIN Saddle binding
position adjustment
0 to 400 200
B FOLDING POSITION Saddle folding
position adjustment
0 to 400 200
C FRONT ADJUST Alignment position
adjustment (front)
0 to 20 10
D REAR ADJUST Alignment position
adjustment (rear)
0 to 20 10
E STAPLE REAR Staple binding
position adjustment
(one position at the
rear)
0 to 200 100
F STAPLE FRONT Staple binding
position adjustment
(one position in front)
0 to 200 100
G STAPLE BOTH Staple binding
position adjustment
(two positions at the
center)
0 to 200 100
H STAPLE PITCH Staple binding
position adjustment
(two positions in
pitch)
0 to 100 50
I PUNCH CENTER Punch center
adjustment
47 to 53 50
J PUNCH HOLE Punch hole position
adjustment
0 to 100 50
Item Display Item
Set
range
Default
value
A FRONT ADJUST Alignment position
adjustment (front)
2 to 18 10
B REAR ADJUST Alignment position
adjustment (rear)
2 to 18 10
C STAPLE REAR Staple binding position
adjustment (one
position at the rear)
68 to 132 100
D STAPLE FRONT Staple binding position
adjustment (one
position in front)
68 to 132 100
E STAPLE BOTH Staple binding position
adjustment (two
positions at the
center)
68 to 132 100
0
SIMULATION
NO.03
03
TEST
FIN LOAD CHECK
EXECUTE
FINRPS
FJPM
FJFM FFM
FPM FAM
FFJM FRJM
FSM FFSM
FLM
FF
CLOSE
1/1
1/1
F STAPLE PITCH Staple binding position
adjustment (two
positions in pitch)
68 to 132 100
G PUNCH CENTER Punch center
adjustment
37 to 63 50
H PUNCH HOLE Punch hole position
adjustment
42 to 58 50
DCSI1 Desk 1 installation detection
DPFD1 Desk 1 transport detection
DLUD1 Desk 1 upper limit detection
DPED1 Desk 1 paper empty detection
DCSPD1 Desk 1 remaining paper quantity detection
DCSS11 Desk 1 rear edge detection 1
DCSS12 Desk 1 rear edge detection 2
DCSS13 Desk 1 rear edge detection 3
DCSS14 Desk 1 rear edge detection 4
DCSI2 Desk 2 instillation detection
DPFD2 Desk 2 transport detection
DLUD2 Desk 2 upper limit detection
DPED2 Desk 2 paper empty detection
DCSPD2 Desk 2 remaining paper quantity detection
DCSS21 Desk 2 rear edge detection 1
DCSS22 Desk 2 rear edge detection 2
DCSS23 Desk 2 rear edge detection 3
DCSS24 Desk 2 rear edge detection 4
DSW_DSK Desk transport cover open/close detection
LPFD LCC transport sensor
LUD LCC tray upper limit sensor
LDD LCC tray lower limit sensor
LPED LCC tray paper empty sensor
LCD LCC tray insertion detection
LDSW LCC upper open/close detection SW
LRE LCC lift motor encoder sensor
L24VM LCC24V power monitor
LLSW LCC upper limit SW
LTOD LCC main unit connection detection
Item Display Item
Set
range
Default
value
0
:
A㧦200
B㧦200
C㧦 10
D㧦 10
㧧
SADDLE POSITION
㧧
FOLDING POSITION
㧧
FRONT ADJUSUT
㧧
REAR ADJUSUT
SIMULATION
NO.03-10
FINISHER ADJUSTMENT
200
㨇
0
㨪
400
㨉
OK
TEST
CLOSE
To Next Page
Loading...
