MX-2300/2700 N/G SIMULATION 7 – 29
26-2
Purpose : Setting
Function (Purpose) : Used to set the paper size of the large
capacity tray (LCC). (When the paper size
is changed, this simulation must be exe-
cuted to change the paper size in software.)
Section : Paper feed
Item : Setting
Operation/Procedure
Select the paper size with the buttons on the touch panel.
26-3
Purpose : Setting
Function (Purpose) : Used to set the specifications of the auditor.
Section : Auditor
Item : Specifications
Operation/Procedure
Select the set target with the button on the touch panel.
When a button is pressed, the set content is saved.
(*): AR-C260 series VENDOR MODE is supported.
Operation 1: Wait for auto clear setting time. Default, 60sec. Can
be changed by the system setting.
Operation 2: Auto clear is not made.
Operation 3: Setting is immediately cleared. The display returns to
the initial screen.
26-5
Purpose :Setting
Function (Purpose) : Used to set the count mode of the total
counter and the maintenance counter.
Section :—
Item : Counter
Operation/Procedure
1) Select the set item with [↑] [↓] buttons.
2) Enter the set value with 10-key.
3) Press [OK] button.
The set content in step 2) is saved. (Count-up number for A3
paper is 1 or 2.)
* 1 = Count up by 1
2 = Count up by 2
LCC 0 8.5 x 11 (Default: U.S.A, Canada, Inch)
1 A4 (Japan, AB_B, Europe, U.K,
Australia, AB_A)
2B5
Item
Button
display
Content Default
BUILT-IN
AUDITOR
P10 Built-in auditor mode
(standard mode) operation
P10
EC1 The built-in auditor mode is
changed to EC1.
OUTSIDE
AUDITOR
NONE Normal operation NONE
P VENDOR1 Vendor mode for old-type coin
vendor. Control in the copy
mode only.
P OTHER Vendor mode for the other
external auditor connected to
the coin vendor I/F
DOC ADJ ON Document filing function
enabled
OFF
OFF Document filing function
disabled
PF ADJ ON Continuous paper feed is
performed.
OFF
OFF Continuous paper feed is not
performed.
VENDOR
MODE (*)
MODE1 Vendor mode 1 MODE3
MODE2 Vendor mode 2
MODE3 Vendor mode 3
1/1
SIMULATION NO.26-02
TEST
SIZE SETUP
8.5 11
LCC
A4
0
B5
CLOSE
COUNTUP
TIMING1
FUSER_IN The charging timing is when
passing the sensor paper lead
edge after fusing.
EXIT_OUT
FUSER_OUT The charging timing is when
passing the sensor paper rear
edge after fusing.
EXIT_OUT The charging timing is when
passing the (machine, right)
tray/after-process unit paper
exit sensor paper rear edge.
Diagnosis
setting
The
specified
quantity is
completed.
Remainder
of money
left.
Insufficient money during
copy job
The
specified
quantity is
completed.
No
remainder
of money.
BLACK/
COLOR (No
remainder
of money)
COLOR
(Remainder
of money
left)
Condition 1 Condition 2 Condition 3 Condition 4
MODE1 Operation 1 Operation 2 Operation 2 Operation 1
MODE2 Operation 1 Operation 1 Operation 2 Operation 1
MODE3 Operation 1 Operation 3 Operation 2 Operation 3
Item Display Content
Setting
range *
Default
A TOTAL (B/W) Total counter (BLACK) 1 to 2 2
B TOTAL (COL) Total counter (COLOR) 1 to 2 2
C MAINTENANCE
(B/W)
Maintenance counter
(BLACK)
1 to 2 2
D MAINTENANCE
(COL)
Maintenance counter
(COLOR)
1 to 2 2
E DEV (B/W) Developer counter
(BLACK)
1 to 2 2
F DEV (COL) Developer counter
(COLOR)
1 to 2 2
Item
Button
display
Content Default
0
SIMULATION
NO.26-03
TEST
AUDITOR SETUP
P10
BUILT-IN
AUDITOR
EC1
㧦
CLOSE
1/2
P OTHER
OUTSIDE
AUDITOR
㧦
NONE
P VENDOR1
㧦
ON
OFF
DOC
ADJ
㧦
ON
OFF
PF
ADJ
㧦
MODE1
MODE3
VENDOR MODE
MODE2
To Next Page
Loading...
