Sharp MX-2300 G - Page 136

MX-2300/2700 N/G SIMULATION 7 – 30
26-6
Purpose : Setting
Function (Purpose) : Used to set the specifications (paper, fixed
magnification ratio, etc.) of the destination.
Section :—
Item : Specifications (Destination)
Operation/Procedure
1) Select the set target with the button on the touch panel.
2) Press [EXECUTE] button.
The selected set content is saved.
26-10
Purpose : Setting
Function (Purpose) : Used to set the trial mode of the network
scanner.
Section :—
Item : Operation
Operation/Procedure
1) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
2) When [OK] button is pressed, the current entered value is
saved to EEPROM and RAM.
* When [COLOR], or [BLACK] key is pressed, the value is
saved to EEPROM and RAM.
<Setting range and default value of each set value>
26-18
Purpose :Setting
Function (Purpose) : Used to set the toner save mode.
Section :—
Item :—
Operation/Procedure
1) Use [↑] and [↓] buttons to select an item.
The set value is highlighted and the value is displayed in the
setting area.
* When there is an item over [↑], the display becomes active
and shifts to another item.
When there is no item over [↑], the display grays out and the
operation is disabled.
When there is an item under [↓], the display becomes active
and shifts to another item.
When there is no item under [↓], the display grays out and
the operation is disabled.
2) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
3) When [OK] button is pressed, the current entered value is
saved to EEPROM and RAM.
* When [↑], [↓] button, [COLOR], or [BLACK] key is pressed,
the value is saved to EEPROM and RAM.
<Setting range and default value of each set value>
U.S.A. United States of America
CANADA Canada
INCH Inch series, other destinations
JAPAN Japan
AB_B AB series (B5 detection), other destinations
EUROPE Europe
U.K. United Kingdom
AUS. Australia
AB_A AB series (A5 detection), other destinations
CHINA China
Item Display Content
Setting
range
Default
value
A TRIAL MODE
(0:YES 1:NO)
0 Trial mode setting 0 to 1 1
1 Trial mode cancel
0
A
:
A㧦 2
B㧦 2
C㧦 2
D㧦 2
㧧 TOTAL(B/W)
㧧 TOTAL(COL)
㧧 MAINTENANCE(B/W)
㧧 MAINTENANCE(COL)
SIMULATION  NO.26 㧙 05
A3(1117) COUNTUP
2
㨇 1㨪 2 㨉
OK
TEST
CLOSE
0
SIMULATI ON  NO.26-06
TEST
DISTINATION SETUP
EXECUTE
1/1
U.S.A
CANADA
INCH JAPAN
AB_B EUROPE
U.K.
AUS
AB_A CHIN
A
CLOSE
Item Display Content
Setting
range
Default
value
ACOPY
(1:YES 0:NO)
0 Copy toner save mode
is allowed
0 to 1 0
1 Copy toner save mode
is inhibited.
B PRINTER
(1:YES 0:NO)
0 Printer toner save
mode is allowed.
0 to 1 0
1 Printer toner save
mode is inhibited.
0
A:
A:1
 TRIAL MODE (0:YES 1:NO)
SIMULATION NO.26-10
NETWORK SCANNER TRIAL MODE SETUP
1
[0~ 1]
OK
TEST
CLOSE
0
A
:
A㧦 0
B㧦 0
㧧 COPY(1:YES 0:NO)
㧧 PRINTER(1:YES 0:NO)


SIMULATION  NO.26 㧙 18
TONER SAVE MODE SETUP
0
㨇 0㨪 1 㨉
OK
TEST
CLOSE