MX-2300/2700 N/G SIMULATION 7 – 31
26-30
Purpose : Setting
Function (Purpose) : Used to set allow/inhibit of HL slow-up con-
trol (CE mark support control).
Section :—
Item : Specifications (Operation mode (common
operation))
Operation/Procedure
1) When the machine enters the simulation, the following screen
is displayed.
2) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
3) When [OK] button is pressed, the current entered value is
saved to EEPROM and RAM.
* When [COLOR], or [BLACK] key is pressed, the current set
value is saved to EEPROM and RAM.
<Setting range and default value of each set value>
NOTE: Even though the control is allowed, the CE mark support
control may not be executed depending on the power fre-
quency, etc.
<Initial value and set value linked with the destination>
26-35
Purpose : Setting
Function (Purpose) : Used to set the trouble memory saving pro-
cedure.
Section :—
Item :—
Operation/Procedure
1) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
2) When [OK] button is pressed, the current entered value is
saved to EEPROM and RAM.
* When [COLOR], or [BLACK] key is pressed, the current set
value is saved to EEPROM and RAM.
<Setting range and default value of each set value>
26-38
Purpose :Setting
Function (Purpose) : Used to set Continue/Stop of print when the
developer life is reached.
Section : Other
Item : Specifications (Operation mode)
Operation/Procedure
1) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
2) When [OK] button is pressed, the current entered value is
saved to EEPROM and RAM.
* When [COLOR], or [BLACK] key is pressed, the current set
value is saved to EEPROM and RAM.
<Setting range and default value of each set value>
26-41
Purpose :Setting
Function (Purpose) : Used to set YES/NO of AMS setting in the
center binding mode.
Section :—
Item : Specifications (Operation mode)
Operation/Procedure
1) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
2) When [OK] button is pressed, and the current entered value is
saved to EEPROM and RAM.
Item Display Content
Setting
range
Default value
A (0:YES 1:NO) 0 CE mark
control allowed
0 to 1 Refer to <Initial
value and set
value linked with
the destination>.
1 CE mark
control inhibited
Destination Setting value
U.S.A 1 (CE not supported)
CANADA 1 (CE not supported)
INCH 1 (CE not supported)
JAPAN 1 (CE not supported)
AB_B 1 (CE not supported)
EUROPE 0 (CE supported)
U.K 0 (CE supported)
AUS. 0 (CE supported)
AB_A 0 (CE supported)
CHINA 0 (CE supported)
:
A㧦 1
㧧
(0:YES 1:NO)
SIMULATION
NO.26-30
CE MARK CONTROL SETTING
1
[0~1]
OK
TEST
0
CLOSE
Item Display Content
Setting
range
Default
value
A (0:ONCE
1:ANY)
0 Only once. If same as the
previous one, it is not saved.
0 to 1 0
1 Any time. Though same as
the previous one, it is saved.
Item Display Content
Setting
range
Default
value
A MAINTENANCE
LIFE OVER
(0:CONTINUE
1:STOP)
0 Continue/Stop setting
of print when the
maintenance life is
over (Print Continue)
0 to 1 0
1 Continue/Stop setting
of print when the
maintenance life is
over (Print Stop)
0
:
A㧦 0
㧧 (0:ONCE 1:ANY)
SIMULATIO N
NO.26-35
TROUBLE MEMORY MODE SETUP
0
㨇 0㨪 1 㨉
OK
TEST
CLOSE
0
A:
A㧦 0
MAINTENANCE LIFE OVER (0:CONTINUE 1:STOP)
SIMULATION NO.26-38
ENGINE LIFE OVER SETTING
0
[0~ 1]
OK
TEST
CLOSE
To Next Page
Loading...
