MX-2300/2700 N/G SIMULATION 7 – 32
* When [COLOR], or [BLACK] key is pressed, the current set
value is saved to EEPROM and RAM.
<Setting range and default value of each set value>
<Initial value and set value liked with the destination>
26-49
Purpose : Setting
Function (Purpose) : Used to set the copy speed mode.
Section :—
Item : Setting
Operation/Procedure
1) When the machine enters Simulation 26-49, the current set
status is displayed.
* The current set button is highlighted.
2) Select an item to be changed, and it is highlighted. The setting
is saved to EEPROM and RAM.
* Only one can be selected for each item.
<Item description>
26-50
Purpose :Setting
Function (Purpose) : Used to set functions.
Section :—
Item : Specifications (Operation)
Operation/Procedure
1) Select an item to be set with [↑] and [↓] buttons.
The selected value is highlighted and the value is displayed in
the setting area.
* When there is an item over [↑], the display becomes active
and shifts to another item.
When there is no item over [↑], the display grays out and the
operation is disabled.
When there is an item under [↓], the display becomes active
and shifts to another item.
When there is no item under [↓], the display grays out and
the operation is disabled.
2) Enter the set value with 10-key.
* Press [C] key to clear the entered value.
3) When [OK] button is pressed, the entered value is set.
* When [↑], [↓] button, [COLOR], or [BLACK] key is pressed,
the current set value is saved to EEPROM and RAM.
<Setting range and default value of each set value>
<Display when 2-color/Single color inhibit>
* OFF: Inhibit cancel state
ON: Inhibit state
Item Display Content
Setting
range
Default value
A (0:YES
1:NO)
0 Center binding
mode AMS setting
0 to 1 Refer to <Initial
value and set
value linked with
the destination>.
1 Center binding
mode AMS cancel
Destination Setting value
U.S.A 0 (Cancel)
CANADA 0 (Cancel)
INCH 0 (Cancel)
JAPAN 0 (Cancel)
AB_B 0 (Cancel)
EUROPE 1 (Setting)
U.K 1 (Setting)
AUS. 0 (Cancel)
AB_A 0 (Cancel)
CHINA 0 (Cancel)
Item
Set
value
Content
Default
value
POSTCARD LOW Postcard copy speed LOW LOW
HIGH Postcard copy speed HIGH
0
:
A㧦 0
㧧 (0:YES 1:NO)
SIMULATION
NO.26-41
PAMPHLET MODE AMS SETTING.
0
㨇 0㨪 1 㨉
OK
TEST
CLOSE
1/1
SIMULATION
NO.26-49
TEST
COPY SPEED MODE SETUP
LOW
POSTCARD㧦
HIGH
0
CLOSE
Item Display
Content
description
Setting
range
Default value
ABW
REVERSE
YES B/W REVERSE
allowed
0 – 1 <Setting range
and default
value of each
set value>
Refer to
"Setting value
A."
NO B/W REVERSE
inhibited
0 – 1
B COLOR MODE 2-color/Single
color inhibit
setting
0 to 7 <Setting range
and default
value of each
set value>
Refer to
"Setting value
B."
C FINISHER
FUNCTION
YES The number of
discharge of
special paper
from the finisher
is limited.
0 – 1 0 (YES)
NO The number of
discharge of
special paper
from the finisher
is not limited.
0 – 1
Mode inhibit
When 2-color/
Single color inhibit
SIM setting
Single 2-color
OFF OFF OFF 0
OFF ON OFF 1
ON OFF OFF 2
ON ON OFF 3
OFF OFF ON 4
OFF ON ON 5
ON OFF ON 6
ON ON ON 7
To Next Page
Loading...
