Siemens SIMOCODE DP - Page 98

102 pages

To Next Page

To Previous Page

Parameter

A.2Block Parameter Of SIMO_CHN

SIMOCODE DP PCS 7 Library Migration (Legacy) - V9.1 SP2

98 Programming and Operating Manual, 11/2022, A5E51265657002A/RS-AC/003

Main Page

Table of Contents3
Introduction7
Security Information7
Information on Data Protection7
Product Specific Security Information8
Product Discontinuation of SIMOCODE DP Hardware8
Components of the Software Package9
Configuration Steps10
Configuring in HW Config10
Modifying the System During Operation Via Cir11
Configuring in CFC11
Driver Generator12
Generate Module Drivers12
Requirements for Generating the Module Drivers13
Driver Blocks13
Object Lists and Action Lists13
Example Configurations14
SIMOCODE DP Behind DP Master System15
PDM: SIMOCODE DPV1 Basic Type Selection16
GSD: SIMOCODE-DPV1 (S7-Compatible) Basic Type Selection17
PDM: SIMOCODE-DPV1 (S7-Compatible) Basic Type Selection17
Network Configuration19
SIMOCODE DP Behind the Y-Link19
GSD: SIMOCODE DP Basic Type Selection19
PDM: SIMOCODE DP Basic Type Selection21
Redundant PLC DP Operating Mode21
Network Configuration22
SIMOCODE DP Behind the IE/PB Link PN IO23
GSD: SIMOCODE DP Basic Type Selection23
PDM: SIMOCODE DP Basic Type Selection23
Network Configuration25
SIMOCODE DP Behind the IE/PB Link HA25
GSD: SIMOCODE DP Basic Type Selection25
PDM: SIMOCODE DP Basic Type Selection26
Network Configuration28
Sample Project Configuration28
Update an Existing PCS 7 Project29
Further Documentation29
Templates31
Supported Control Functions31
Overview of the Templates, Control Functions and Blocks31
Using Templates32
SIMODIAG Function35
Description35
Object Name (Type+Number)35
Calling Obs35
Scope of Application35
Use in CFC35
Startup Response36
DP Master and DP Slave Failure36
Module Error36
I / O Access Error37
Diagnostic Data Reading37
Error Handling37
Messages37
Operator Control and Monitoring37
Message Texts and Auxiliary Process Values38
SIMO_CHN Function39
Description39
Object Name (Type+Number)39
Calling Obs39
Function39
Principle of Operation40
Module Failure40
Simulation40
Local / Remote Switch-Over of the Control Station41
Interlocking41
MANUAL / AUTOMATIC Operation42
Manual-Linked / Manual-Operator42
Monitoring of Control Commands43
Motor Current Monitoring43
Statistic and Diagnostic Functions43
Reading and Writing Data Records44
Suppressing of Reading and Writing47
Reset Response47
Additional Functions48
Startup Response48
Time-Related Characteristics48
Bumpless Changeover48
Error Handling48
Messages48
Faceplate Actuation49
Message Texts and Auxiliary Process Values49
AS Block Parameters in the CFC51
Description of Parameters54
Control Functions54
INBT2 Assignment56
OBT2 Assignment57
SIMO_STAT Status Display58
VSTATUS and VSTATUS1 Status Display58
Block Icon and Faceplate60
Block Icons60
Faceplate61
Standard View62
Limits View63
Maintenance View64
Statistic View65
Trend View66
Alarms View66
Faults View67
Warnings View68
Batch View69
Status Display69
Maintenance Station73
Maintenance Station Block Icons82
Maintenance State and Maintenance Job83
Parameter85
Block Parameter of SIMODIAG85
Description of Parameters86
OMODE Structure86
Block Parameter of SIMO_CHN87
Technical Data99
Header Information99
Attributes of the Blocks100
Abbreviations101

Siemens SIMOCODE DP - Page 98

Table of Contents

Related product manuals