Siemens SIPART PS2 User Manual

8.3.1.2 '2.YAGL' Rated angle of rotation of feedback ......................................................................143
8.3.1.3 '3.YWAY' Range of stroke....................................................................................................144
8.3.1.4 '4.INITA' Initialization (automatically) ...................................................................................145
8.3.1.5 '5.INITM' Initialization (manual) ............................................................................................145
8.3.2 Application parameters 6 to 55 ............................................................................................145
8.3.2.1 '6.SDIR' Setpoint direction ...................................................................................................145
8.3.2.2 '7.TSUP' Setpoint ramp UP / '8.TSDO' Setpoint ramp DOWN.............................................146
8.3.2.3 '9.SFCT' Setpoint function....................................................................................................146
8.3.2.4 '10.SL0' ... '30.SL20' Setpoint turning point..........................................................................147
8.3.2.5 '31.DEBA' Deadband of controller........................................................................................148
8.3.2.6 '32.YA' Manipulated variable limiting Start / '33.YE' Manipulated variable limiting End .......148
8.3.2.7 '34.YNRM' Manipulated variable standardization.................................................................149
8.3.2.8 '35.YDIR' Direction of action of manipulated variable for display and position feedback.....150
8.3.2.9 ' 36.YCLS' Tight closing/fast closing with manipulated variable...........................................150
8.3.2.10 '37.YCDO' Value for tight closing/fast closing Down............................................................151
8.3.2.11 '38.YCUP' Value for tight closing/fast closing Up.................................................................152
8.3.2.12 '38.YCUP' Upper value for tight closing / fast closing ..........................................................152
8.3.2.13 '39.BIN1' / '40.BIN2' Function of binary inputs .....................................................................153
8.3.2.14 '41.AFCT' Alarm function .....................................................................................................154
8.3.2.15 '42.A1' / '43.A2' Alarm response threshold...........................................................................156
8.3.2.16 '44.\\FCT' Function fault message........................................................................................156
8.3.2.17 '45.\\TIM' Monitoring time for setting of fault message 'Control deviation' ...........................157
8.3.2.18 '46.\\LIM' Response threshold of fault message 'Control deviation' .....................................157
8.3.2.19 '47.\\STRK' Limit monitoring for the number of total strokes ................................................158
8.3.2.20 '48.PRST' Preset..................................................................................................................158
8.3.2.21 '49.PNEUM' Pneumatics type ..............................................................................................159
8.3.2.22 '50.XDIAG' Activation of extended diagnostics ....................................................................160
8.3.2.23 '51.FSTY' Safety position .....................................................................................................161
8.3.2.24 '52.FSTI' Monitoring time to set the safety position..............................................................162
8.3.2.25 '53.FSVL' Safety setpoint .....................................................................................................162
8.3.2.26 '54.STNR' Station number....................................................................................................162
8.3.2.27 '55.IDENT' Device operating mode (ID No.) ........................................................................162
8.3.3 Extended diagnostics parameters A to P .............................................................................163
8.3.3.1 Partial stroke test 'A.\\PST'...................................................................................................163
8.3.3.2 Monitoring of dynamic control valve behavior 'b.\\DEVI' ......................................................168
8.3.3.3 Monitoring/compensation of pneumatic leakage 'C.\\LEAK'.................................................170
8.3.3.4 Monitoring of stiction (slipstick) 'd.\\STIC'.............................................................................173
8.3.3.5 Monitoring of deadband 'E.\\DEBA'......................................................................................175
8.3.3.6 Monitoring the lower endstop ''F.\\ZERO'.............................................................................176
8.3.3.7 Monitoring the upper endstop 'G.\\OPEN' ............................................................................177
8.3.3.8 Monitoring the lower limit temperature 'H.\\TMIN' ................................................................179
8.3.3.9 Monitoring the upper limit temperature 'J.\\TMAX' ...............................................................180
8.3.3.10 Monitoring of number of total strokes 'L.\\STRK'..................................................................182
8.3.3.11 Monitoring of number of changes in direction 'O.\\DCHG' ...................................................183
8.3.3.12 Monitoring the position average value 'P.\\PAVG'................................................................185
9 Functions/operations using PROFIBUS PA .............................................................................................189
9.1 System integration ...............................................................................................................189
9.2 Acyclic data transfer.............................................................................................................189
9.2.1 Acyclic data transfer using SIMATIC PDM...........................................................................189
9.2.2 'Device' menu.......................................................................................................................190
9.2.2.1 Load to device......................................................................................................................190
Table of contents
SIPART PS2 with PROFIBUS PA
6 Operating Instructions, 05/2019, A5E00127926-AC

Siemens SIPART PS2 Specifications

General

Supply Pressure	1.4 to 7 bar (20 to 100 psi)
Enclosure Rating	IP66/NEMA 4X
Communication Protocols	HART, PROFIBUS PA, FOUNDATION Fieldbus
Output Pressure	0 to 100% of supply pressure
Hazardous Area Certification	ATEX, IECEx, FM, CSA
Type	Electropneumatic
Input Signal	4-20 mA
Rotation Angle	30° to 90°
Operating Temperature	-40°C to +80°C
Mounting	Linear and rotary actuators
Air Consumption	Typically less than 0.1 kg/h