To Next Page

To Previous Page

TC63 AT Command Set

11.17 ATA

TC63_ATC_V00.490 Page 303 of 501 5/24/05

Confidential / Draft - Do not copy

11.17 ATA Manual response to a network request for PDP context acti-

vation

The V.250 ATA command may be used to accept a network request for a PDP context activation announced by

the unsolicited result codes "RING" or "+CRING: GPRS". The MT responds with CONNECT, enters V.250 online

data state and follows the same procedure as it would after having received a AT+CGANS=1 with no <L2P> or

<cid> values specified.

If you try to answer a request which is no longer present or which is already answered by another instance, NO

CARRIER is returned.

Syntax

Exec Command

ATA

Response(s)

CONNECT

NO CARRIER

Reference(s) PIN ASC0 ASC1 USB MUX1 MUX2 MUX3 Charge 4 Last

GSM 07.07 % % % % % % % ! ! %

Default Chapter3
- Table of Contents3
1 Introduction14
- Scope of the Document14
- Related Documents15
- Document Conventions16
- AT Command Syntax18
- Supported Character Sets20
- Serial Interface Flow Control26
  - Software Flow Control (XON/OFF Handshake)26
  - Hardware Flow Control (RTS/CTS Handshake)26
- Unsolicited Result Code Presentation27
  - Communication between Customer Application and TC6327
- Common PCN Handset Specification (CPHS)28
- Errors and Messages29
2 Configuration Commands30
- AT&F Set All Current Parameters to Manufacturer Defaults30
- AT&V Display Current Configuration31
- AT&W Stores Current Configuration to User Defined Profile34
- ATQ Set Result Code Presentation Mode35
- ATV Set Result Code Format Mode36
  - Verbose and Numeric Result Codes36
- ATX Set CONNECT Result Code Format and Call Monitoring37
- AT\V Set CONNECT Result Code Format38
- ATZ Set All Current Parameters to User Defined Profile39
- AT+CFUN Set Phone Functionality40
- AT^SMSO Switch off Mobile Station44
- AT+GCAP Request Complete TA Capabilities List45
- AT+CMEE Mobile Equipment Error Message Format46
- AT+CSCS Select te Character Set51
- AT^SCFG Extended Configuration Settings52
- AT^SM20 Set M20 Compatibility Mode65
3 Status Control Commands66
- AT+CMER Mobile Equipment Event Reporting66
- AT+CIND Indicator Control68
- AT^SIND Extended Indicator Control71
- AT+CEER Extended Error Report78
- ATS18 Extended Call Release Report85
- AT+CPAS Mobile Equipment Activity Status87
- AT+WS46 Select Wireless Network88
4 Serial Interface Control Commands89
- AT\Q Flow Control89
- AT&C Set Circuit Data Carrier Detect (DCD) Function Mode90
- AT&D Set Circuit Data Terminal Ready (DTR) Function Mode91
- AT&S Set Circuit Data Set Ready (DSR) Function Mode92
- ATE Enable Command Echo93
- AT+ICF Serial Interface Character Framing94
- AT+IFC Set Flow Control Separately for Data Directions96
- AT+ILRR Set TE-TA Local Rate Reporting98
- AT+IPR Set Fixed Local Rate100
  - Autobauding101
- AT+CMUX Enter Multiplex Mode103
- AT^STPB Transmit Parity Bit (for 7E1 and 7O1 Only)107
5 Security Commands108
- AT+CPIN PIN Authentication108
  - What to Do if PIN or Password Authentication Fails110
- AT+CPIN2 PIN2 Authentication112
- AT^SPIC Display PIN Counter114
- AT+CLCK Facility Lock118
- AT^SLCK Facility Lock123
- AT+CPWD Change Password124
- AT^SPWD Change Password128
- AT^SCSL Customer SIM Lock130
6 Identification Commands134
- ATI Display Product Identification Information134
- AT+CGMI Request Manufacturer Identification135
- AT+GMI Request Manufacturer Identification135
- AT+CGMM Request Model Identification136
- AT+GMM Request Model Identification136
- AT+CGMR Request Revision Identification of Software Status137
- AT+GMR Request Revision Identification of Software Status137
- AT+CGSN Request International Mobile Equipment Identity (IMEI)138
- AT+GSN Request International Mobile Equipment Identity (IMEI)138
- AT+CIMI Request International Mobile Subscriber Identity (IMSI)139
7 Call Related Commands140
- Call Status Information140
- ATA Answer a Call141
- ATD Mobile Originated Call to Specified Number142
- Atd><Mem><N> Mobile Originated Call Using Specific Memory and Index Number144
- Atd><N> Mobile Originated Call from Active Memory Using Index Number146
  - Atd><Str> Mobile Originated Call from Active Memory Using Corresponding Field147
- ATDI Mobile Originated Call to ISDN Number148
- ATDL Redial Last Number Used149
- ATH Disconnect Existing Connection150
- AT+CHUP Hang up Call151
- AT^SHUP Hang up Call(S) Indicating a Specific GSM04.08 Release Cause152
- ATS0 Set Number of Rings before Automatically Answering a Call154
- ATS6 Set Pause before Blind Dialing155
- ATS7 Set Number of Seconds to Wait for Connection Completion156
- ATS8 Set Number of Seconds to Wait for Comma Dialing Modifier157
- ATS10 Set Disconnect Delay after Indicating the Absence of Data Carrier158
- ATO Switch from Command Mode to Data Mode / PPP Online Mode159
- Switch from Data Mode to Command Mode160
- AT+CBST Select Bearer Service Type161
- AT+CRLP Select Radio Link Protocol Parameters for Originated Non-Transparent Data Calls163
- AT+CLCC List Current Calls of ME164
- AT^SLCC Siemens Defined Command to List Current Calls of ME166
- AT+CR Service Reporting Control172
- AT+CRC Set Cellular Result Codes for Incoming Call Indication173
- AT+CSNS Single Numbering Scheme174
- AT^SCNI List Call Number Information175
- AT^SLCD Display Last Call Duration176
- AT^STCD Display Total Call Duration177
- ATP Select Pulse Dialing178
- ATT Select Tone Dialing178
8 Network Service Commands179
- AT+COPN Read Operator Names179
- AT+COPS Operator Selection180
- AT^SOPS Extended Operator Selection182
- AT+CREG Network Registration184
- AT+CSQ Signal Quality187
- AT^SMONC Cell Monitoring188
- AT^SMOND Cell Monitoring190
- AT^MONI Monitor Idle Mode and Dedicated Mode193
  - AT^MONI Responses194
  - Service States195
- AT^MONP Monitor Neighbour Cells196
  - AT^MONP Responses197
- AT^SMONG GPRS Monitor198
  - AT^SMONG Cell Info Table199
- AT^SALS Alternate Line Service200
- AT^SHOM Display Homezone202
- AT^SPLM Read the PLMN List203
- AT+CPOL Preferred Operator List204
- AT^SPLR Read Entry from the Preferred Operators List205
- AT^SPLW Write an Entry to the Preferred Operators List206
9 Supplementary Service Commands207
- AT+CACM Accumulated Call Meter (ACM) Reset or Query207
- AT^SACM Advice of Charge and Query of ACM and Acmmax208
- AT+CAMM Accumulated Call Meter Maximum (Acmmax) Set or Query210
- AT+CAOC Advice of Charge Information211
- AT+CCUG Closed User Group212
- AT+CCFC Call Forwarding Number and Conditions Control214
- AT+CCWA Call Waiting218
- AT+CHLD Call Hold and Multiparty222
- AT+CLIP Calling Line Identification Presentation224
- AT+CLIR Calling Line Identification Restriction226
- AT+COLP Connected Line Identification Presentation227
- AT+CPUC Price Per Unit and Currency Table229
- AT+CSSN Supplementary Service Notifications231
- AT+CUSD Supplementary Service Notifications233
10 Internet Service Commands235
- AT^SICS Internet Connection Setup Profile237
- AT^SISS Internet Service Setup Profile242
- AT^SISO Internet Service Open254
  - Example: Accepting / Rejecting Socket Connection Request from Remote Client257
- AT^SISC Internet Service Close259
  - Effect of Parameter <Closemode260
- AT^SISR Internet Service Read Data261
- AT^SISW Internet Service Write Data263
- Information Elements Related to Internet Service Urcs265
11 GPRS Commands268
- AT+CGACT PDP Context Activate or Deactivate268
- AT+CGANS Manual Response to a Network Request for PDP Context Activation270
- AT+CGATT GPRS Attach or Detach272
- AT+CGAUTO Automatic Response to a Network Request for PDP Context Activation273
- AT+CGDATA Enter Data State275
  - Automatic Deactivation of PDP Context During Dial-Up PPP276
- AT+CGDCONT Define PDP Context277
- AT+CGEQMIN 3G Quality of Service Profile (Minimum Acceptable)279
- AT+CGEQREQ 3G Quality of Service Profile (Requested)283
- AT+CGPADDR Show PDP Address287
- AT+CGQMIN Quality of Service Profile (Minimum Acceptable)288
- AT+CGQREQ Quality of Service Profile (Requested)292
- AT+CGREG GPRS Network Registration Status296
- AT+CGSMS Select Service for MO SMS Messages298
- AT^SGACT Query All PDP Context Activations299
- AT^SGAUTH Set Type of Authentication for PPP Connection301
- AT^SGCONF Configuration of GPRS Related Parameters302
- ATA Manual Response to a Network Request for PDP Context Activation303
- ATD*99# Request GPRS Service304
- ATD*98# Request GPRS IP Service305
- ATH Manual Rejection of a Network Request for PDP Context Activation306
- ATS0 Automatic Response to a Network Request for PDP Context Activation307
- Using GPRS at Commands (Examples)308
- Using the GPRS Dial Command ATD310
12 FAX Commands311
- FAX Parameters311
- AT+FCLASS Fax: Select, Read or Test Service Class312
- AT+FRH Receive Data Using HDLC Framing313
- AT+FRM Receive Data314
- AT+FRS Receive Silence315
- AT+FTH Transmit Data Using HDLC Framing316
- AT+FTM Transmit Data317
- AT+FTS Stop Transmission and Wait318
13 Short Message Service (SMS) Commands319
- SMS Parameters319
- AT+CMGC Send an SMS Command324
- AT+CMGD Delete SMS Message325
- AT+CMGF Select SMS Message Format326
- AT+CMGL List SMS Messages from Preferred Store327
- AT+CMGR Read SMS Messages329
- AT+CMGS Send SMS Message331
- AT+CMGW Write SMS Messages to Memory333
- AT+CMSS Send SMS Messages from Storage335
- AT+CNMA New SMS Message Acknowledge to ME/TE, Only Phase 2336
- AT+CNMI New SMS Message Indications337
- AT+CPMS Preferred SMS Message Storage340
- AT+CSCA SMS Service Centre Address342
- AT+CSCB Select Cell Broadcast Message Indication343
- AT+CSDH Show SMS Text Mode Parameters344
- AT+CSMP Set SMS Text Mode Parameters345
- AT+CSMS Select Message Service347
- AT^SCML List Concatenated SMS Messages from Preferred Store349
- AT^SCMR Read Concatenated SMS Messages351
- AT^SCMS Send Concatenated SMS Messages353
- AT^SCMW Write Concatenated SMS Messages to Memory354
- AT^SLMS List SMS Memory Storage355
- AT^SMGL List SMS Messages from Preferred Store Without Setting Status to REC READ356
- AT^SMGO Set or Query SMS Overflow Presentation Mode or Query SMS Overflow357
- AT^SMGR Read SMS Message Without Setting Status to REC READ359
- AT^SSCONF SMS Command Configuration360
- AT^SSDA Set SMS Display Availability361
- AT^SSMSS Set Short Message Storage Sequence362
14 SIM Related Commands363
- AT+CRSM Restricted SIM Access363
- AT^SXSM Extended SIM Access366
- AT^SCKS Query SIM and Chip Card Holder Status368
- AT^SSET Indicate SIM Data Ready370
- AT^SCID Display SIM Card Identification Number371
- AT+CXXCID Display Card ID372
15 Remote SIM Access (RSA) Commands373
- Figure 15.1: Basic Remote SIM Access Usage Scenario373
16 SIM Application Toolkit (SAT) Commands386
- AT^SSTA SAT Interface Activation386
- SSTN SAT Notification388
- AT^SSTGI SAT Get Information389
- AT^SSTR SAT Response390
17 Phonebook Commands391
- Sort Order for Phonebooks391
- AT+CNUM Read Own Numbers392
- AT+CPBR Read from Phonebook393
- AT+CPBS Select Phonebook Memory Storage396
- AT+CPBW Write into Phonebook398
- AT^SDLD Delete the 'Last Number Redial' Memory401
- AT^SPBC Find First Matching Entry in Sorted Phonebook402
- AT^SPBD Purge Phonebook Memory Storage403
- AT^SPBG Display Phonebook Entries in Alphabetical Order404
- AT^SPBS Step through the Selected Phonebook Alphabetically407
18 Audio Commands411
- Audio Programming Model411
- Figure 18.1: Audio Programming Model411
- ATL Set Monitor Speaker Loudness412
- ATM Set Monitor Speaker Mode412
- AT+CLVL Loudspeaker Volume Level413
- AT+CMUT Mute Control414
- AT+VTD Tone Duration415
- AT+VTS DTMF and Tone Generation416
- AT^SAIC Audio Interface Configuration417
- AT^SNFA Set or Query of Microphone Attenuation419
- AT^SNFD Set Audio Parameters to Manufacturer Default Values421
- AT^SNFI Set Microphone Path Parameters422
- AT^SNFM Set Microphone Audio Path and Power Supply423
- AT^SNFO Set Audio Output (= Loudspeaker Path) Parameter425
- AT^SNFPT Set Progress Tones427
- AT^SNFS Select Audio Hardware Set428
- AT^SNFTTY Signal TTY/CTM Audio Mode Capability431
- AT^SNFV Set Loudspeaker Volume432
- AT^SNFW Write Audio Setting in Non-Volatile Store433
- AT^SRTC Ring Tone Configuration434
19 Hardware Related Commands436
- AT+CCLK Real Time Clock436
- AT+CALA Set Alarm Time437
- AT^SBC Battery Charge Control440
  - Responses Returned by Read Command442
- AT^SBV Battery/Supply Voltage443
- AT^SCTM Set Critical Operating Temperature Presentation Mode or Query Temperature444
- AT^SSYNC Configure SYNC Pin447
  - ME Status Indicated by Status LED Patterns448
  - Table 19.1: Modes of the LED and Indicated ME Functions448
- AT^SSPI Serial Protocol Interface450
20 Miscellaneous Commands457
- A/ Repeat Previous Command Line457
- ATS3 Set Command Line Termination Character458
- ATS4 Set Response Formatting Character459
- ATS5 Write Command Line Editing Character460
- AT^SFDL Enter Firmware Download Mode461
21 Appendix462
- Restricted Access to SIM Data after SIM PIN Authentication462
- Star-Hash (*#) Network Commands463
- Table 21.1: Star-Hash (*#) Command Overview463
- Table 21.2: Abbreviations of Codes and Parameters Used in Table464
- Table 21.3: Star-Hash Command Response Parameters465
- Table 21.4: Star-Hash Commands for Supplementary Services465
- Available at Commands and Dependency on SIM PIN466
- Table 21.5: Available at Commands and Dependency on SIM PIN466
- Availability of at Commands Depending on Operating Mode of ME473
- Table 21.6: Availability of at Commands Depending on Operating Mode of ME473
- AT Command Settings Storable with AT&W480
- Table 21.7: Settings Stored to User Profile on ASC0 / MUX Channel 1480
- Table 21.8: Settings Stored to User Profile on ASC1 / MUX Channels 2 and 3481
- Factory Default Settings Restorable with AT&F483
- Table 21.9: Factory Default Settings Restorable with AT&F483
- Summary of Unsolicited Result Codes (URC)486
- Table 21.10: Summary of Unsolicited Result Codes (URC)486
- AT Command Usability for USB489
- Table 21.11: at Command Usablility for USB489
- Alphabetical List of at Commands496
- Table 21.12: Alphabetical List of at Commands496

Brand	Siemens
Model	TC63
Category	Accessories
Language	English

Siemens TC63 User Manual

Table of Contents

Questions and Answers:

Siemens TC63 Specifications

Related product manuals