Tektronix 1730 Series - Page 9

Contents
v
List of Figures
Figure 2-1: 1730–Series front–panel control locations. 2–2. . . . . . . . . . . . . . . . . . . . .
Figure 2-2: 1730–Series rear panel. 2–8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2-3: Equipment connections for the 1730–Series “Operator’s Checkout
Procedure.” 2–10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2-4: Two–line color bar display in FLAT filter mode. 2–12. . . . . . . . . . . . . . . .
Figure 2-5: Checking vertical gain calibration with the 1730–Series internal
calibrator (CAL) reference. 2–13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2-6: Dual channel, 2–line display of color bar and linearity signals. 2–14. . . .
Figure 2-7: Checking timing with the internal calibrator signal. 2–15. . . . . . . . . . . . .
Figure 2-8: Two–line display of color bar signal with LOW PASS filter on. 2–16. . . .
Figure 2-9: Two–line display of color bar signal with CHROMA filter. 2–17. . . . . . .
Figure 2-10: Two–line display with dual filter selected. 2–17. . . . . . . . . . . . . . . . . . . . .
Figure 2-11: Two–line display with LINE SELECT on. 2–18. . . . . . . . . . . . . . . . . . . . .
Figure 2-12: Two–field display with intensified line in the first displayed field. 2–19.
Figure 2-13: Two–field display with 15 line mode of the LINE SELECT on. 2–19. . .
Figure 2-14: A 1–line sweep rate with 15 continuous lines (from mid field)
displayed using LINE SELECT. 2–20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2-15: Display of vertical interval with magnified 2 field sweep. 2–20. . . . . . . .
Figure 2-16: NTSC graticule. 2–22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2-17: PAL graticule. 2–24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2-18: Dual standard graticule. 2–26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-1: Plug jumper locations and RGB compensation adjustments. 3–2. . . . . .
Figure 3-2: REMOTE connector pin functions. 3–4. . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-3: Common parts used to convert from +28 VDC enable to ground
closure. 3–6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-4: AUXILIARY connector pin functions. 3–7. . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-5: Dimensions of the 1700F00 plain cabinet. 3–8. . . . . . . . . . . . . . . . . . . . . .
Figure 3-6: 1700F02 portable cabinet. 3–9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-7: Rear view of the instrument, shown in the cabinet, with the securing
screws identified. 3–10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3-8: The 1700F05 side-by-side rack adapter. 3–11. . . . . . . . . . . . . . . . . . . . . . .
Figure 3-9: A 1700-Series instrument mounted in a 1700F05 cabinet with a blank
front panel (1700F06) covering the unused side of the cabinet. 3–11. . . . .
Figure 3-10: A 1700F05 side-by-side rack mounting cabinet with an instrument
and a 1700F07 utility drawer. 3–12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .