Toro Reelmaster 5010- H - Page 238

2.Unplugthe48Vdcbatterydisconnecttopreventunexpectedcuttingunitoperation.RefertoConnecting
andDisconnectingthe48VdcBatterySystem(page19).
3.Swapcuttingreelmotor3withacuttingreelmotorfromadifferentcuttingunit.Youcanobtainmore
informationonreplacingthecuttingreelmotorinChapter5ofthe5010-HServiceManual.
4.Pluginthe48Vdcbatterydisconnect.RefertoConnectingandDisconnectingthe48VdcBatterySystem
(page19).
5.Operatethemachine.
Thefaultmovestothe
newposition.
Ifthefaultfollowsthecuttingreelmotortothenewcuttingunit,replacethe
cuttingreelmotor.GotoStep5.
Thefaultrepeatsatthe
originalposition.
Ifthefaultrepeatsatthecuttingunit3position,gotoStep6.
Thefaultstopped
repeating.
Ifthefaultnolongerrepeats,notethepositionchangeofthecuttingreelmotor
inthemaintenancerecordsforthemachine.Shouldthefaultrepeatinthe
future,troubleshootingmayberesumedwhereyouleftoff.GotoReturningthe
MachinetoService(page22)andfollowthestepslisted.
Step5:UseToroDIAGtoprogramthereplacementcuttingreelmotor.
1.Removetheaccesspanelfromtheoutercoverofthecontrolarm.
2.ConnectaPCwithToroDIAGsoftwaretothemachineviaaToroDIAGCable(PartNo.115-1944).Refer
toToroDIAG-QuickStart(page24).
3.UsetheToroDIAGsoftwaretoreprogramthemachineinaccordancewithToroDIAGUser’sGuide.The
replacementcuttingreelmotorisprogrammedduringthereprogrammingofthemachine.
4.DisconnecttheToroDIAGcablefromthemachine.
5.Installtheaccesspanelontotheoutercoverofthecontrolarm.
6.GotoReturningtheMachinetoService(page22)andfollowthestepslisted.
Step6:Swapcuttingunits.
Note:All5cuttingunitsarenotphysicallyidentical.Youcanswaponlycuttingunit3withcuttingunit1
orcuttingunit5.
1.GotoPreparingforTroubleshootingand/orT esting(page22)andfollowthestepslisted.
2.Unplugthe48Vdcbatterydisconnecttopreventunexpectedcuttingunitoperation.RefertoConnecting
andDisconnectingthe48VdcBatterySystem(page19).
3.Swapcuttingunit3withcuttingunit1or5.
4.Pluginthe48Vdcbatterydisconnect.RefertoConnectingandDisconnectingthe48VdcBatterySystem
(page19).
5.Operatethemachine.
Thefaultmovestothe
newposition.
Ifthefaultfollowsthecuttingunit,repairorreplacethecuttingunit.Youcan
obtainmoreinformationoninstallingandadjustingthecuttingunitintheSetup
sectionofthe5010-HOperator'sManual.GotoPreparingforTroubleshooting
and/orTesting(page22)andfollowthestepslisted.
Thefaultrepeatsatthe
originalposition.
Ifthefaultrepeatsatthecuttingunit3position,gotoStep7.
Thefaultstopped
repeating.
Ifthefaultnolongerrepeats,notethepositionchangeofthecuttingunitinthe
maintenancerecordsforthemachine.Shouldthefaultrepeatinthefuture,
troubleshootingmayberesumedwhereyouleftoff.GotoReturningthe
MachinetoService(page22)andfollowthestepslisted.
238