Toshiba B-SX6T Series System Mode Manual

2. SYSTEM MODE EO13-33002
2.2 Parameter Setting
2-18
2.2 Parameter Setting
 Outline of Parameter Setting
In the Parameter Setting mode, various kinds of parameters, such as communication, key, LCD, etc. can be set.
This will allow a use of the printer to comply with your operating conditions.
The Parameter Setting menu contains the following:
NOTE: Baud rate, Data length, Parity, and Transmission control code should be set to the same values as those of the host
computer. Failure to do this causes improper operation.
Character code selection
Character zero selection
Baud rate selection
Data length selection
Stop bit length selection
Parity selection
Flow control code selection
LCD language selection
A
uto forward wait selection
[
PAUSE
]
<2>PARAMETER SET
FONT CODE PC-850
<2>PARAMETER SET
ZERO FONT 0
<2>PARAMETER SET
SPEED 9600bps
<2>PARAMETER SET
DATA LENG. 8bits
<2>PARAMETER SET
STOP BIT 1bit
<2>PARAMETER SET
PARITY EVEN
<2>PARAMETER SET
XON+READY AUTO
<2>PARAMETER SET
LCD ENGLISH
<2>PARAMETER SET
FORWARD WAIT OFF
<2>PARAMETER SET
[
PAUSE
]
[
PAUSE
]
[PAUSE]
[
PAUSE
]
[PAUSE]
[PAUSE]
[
PAUSE
]
[
PAUSE
]
[
PAUSE
]
<2>PARAMETER SET
EURO CODE B0
<2>PARAMETER SET
A
UTO HD CHK OFF
<2>PARAMETER SET
A
CK/BUSY TYPE1
<2>PARAMETER SET
WEB PRINTER OFF
<2>PARAMETER SET
SENS POSI CENTER
<2>PARAMETER SET
EX.I/O TYPE1
<2>PARAMETER SET
PLUG & PLAY OFF
<2>PARAMETER SET
LBL/RBN END TYPE1
<2>PARAMETER SET
PRE PEEL OFF OFF
<2>PARAMETER SET
BACK SPEED STD
Euro code selection
A
uto print head check selection
Centronics ACK/BUSY timing
selection
Web printer function selection
Media sensor selection
Expansion I/O interface type
selection
Plug & Play selection
Label end/Ribbon end selection
Pre-strip selection
Reverse feed speed selection
[
PAUSE
]
[
PAUSE
]
[
PAUSE
]
[
PAUSE
]
[
PAUSE
]
[
PAUSE
]
[
PAUSE
]
[
PAUSE
]
[
PAUSE
]
[
PAUSE
]
<2>PARAMETER SET
MAXI CODE TYPE1
Maxi code specification selection
Control code selection
<2>PARAMETER SET
CODE ESC,LF,NUL
[PAUSE]
[PAUSE]
Strip wait status selection
<2>PARAMETER SET
PEEL OFF STS OFF
[PAUSE]
<2>PARAMETER SET
FEED KEY FEED
Feed key function selection
[
PAUSE
]
[
PAUSE
]
<2>PARAMETER SET
PEEL OFF TRQ R0
Stri
p
motor tor
q
ue selection
<2>PARAMETER SET
KANJI CODE TYPE1
Kanji code selection
[PAUSE]
Head up cut selection
Ribbon save function selection
<2>PARAMETER SET
HEAD UP CUT OFF
<2>PARAMETER SET
RBN SAVE ON (TAG)
[
PAUSE
]
[
PAUSE
]
[PAUSE]
Ribbon type selection
<2>PARAMETER SET
RIBBON NON TRANS
<2>PARAMETER SET
INPUT PRIME OFF
Input prime selection
[
PAUSE
]
[
PAUSE
]
<2>PARAMETER SET
STABILIZER ON
Stabilizer function selection

Toshiba B-SX6T Series Specifications

General

Brand	Toshiba
Model	B-SX6T Series
Category	Printer
Language	English