EasyManuals Logo

Unify OpenStage 40 User Manual

Unify OpenStage 40
144 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #93 background imageLoading...
Page #93 background image
More functions/services 93
Using system functions from outside
DISA (Direct Inward System Access)
If configured (consult your administrator), you can use an external phone like an
internal station
to set up an outgoing external connection via the system. You
can also activate or deactivate the following system functions:
Reset services and functions,
code #0
Æ Page 91
Call forwarding, code
*
1/#1 Æ Page 40
Lock and unlock phone,
code
*
66/#66 Æ Page 82
Save your PIN code,
code
*
93 Æ Page 83
Send a message,
code
*
68/#68 Æ Page 85
Leave an advisory message,
code
*
69/#69 Æ Page 87
Ringing group, code
*
81/#81 Æ Page 110
Group call, code
*
85/#85 Æ Page 110
Caller ID suppression,
code
*
86/#86 Æ Page 79
Camp-on tone, code
*
87/#87 Æ Page 60
Open door, code
*
61 Æ Page 48
Release door opener, code
*
89/#89 Æ Page 49
Control relays, code
*
90/#90 Æ Page 96
Do not disturb, code
*
97/#97 Æ Page 78
Ringer cutoff, code
*
98/#98 Æ Page 78
Dial using speed dial, code
*
7 Æ Page 55
Associated service, code
*
83 Æ Page 92
Prerequisite: Your phone supports tone dialing (DTMF) or you can switch your
phone to tone dialing. The phone is not connected to the system.
j Establish a connection to the system. Enter the station number (consult your
administrator).
j Wait for the continuous tone (if necessary, switch phone to tone dialing) and
enter the internal number assigned to you and the corresponding PIN code.
( Enter the code (only required if programmed in the system).
j Wait for the dial tone and enter the code for example,
*
97 for Do not disturb on.
If necessary, make further entries; refer also to the user guide for dial pulse/
DTMF phones.
or
j Dial the external number.
You can only perform one function/establish one outgoing connection at a
time.
The connection is cleared as soon as the function is successfully
activated.
In the case of an external call, the connection is cleared as soon as one
of the call partners hangs up.

Table of Contents

Other manuals for Unify OpenStage 40

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Unify OpenStage 40 and is the answer not in the manual?

Unify OpenStage 40 Specifications

General IconGeneral
Resolution240 x 128 pixels
Full duplexYes
Camera includedNo
Dimensions (WxDxH)270 x 220 x 70 mm
Networking featuresQoS
Supported network protocolsIEEE 802.1Q (VLAN), IEEE 802.1p
Dialer locationBase
Phonebook capacity- entries
Volume controlDigital
Voice codecsG.711, G.722
Display number of lines6 lines
Display number of colorsMonochrome
Product colorBlack, Silver
Storage temperature (T-T)-40 - 70 °C
Operating temperature (T-T)5 - 40 °C
CertificationCE, EMC EN55022 Cl. B, EN55024, EN61000-4-11, EN61000-3-2, EN60950-1, EMC (FCC) P.15 (CFR 47) Cl. B, UL60950-1/CSA 22.2 No950
Weight and Dimensions IconWeight and Dimensions
Weight1068 g

Related product manuals