Need help?Do you have a question about the Vaisala AWS310-SITE and is the answer not in the manual?
General| Measurement Parameters | Temperature, Humidity, Wind Speed, Wind Direction, Barometric Pressure, Precipitation |
|---|---|
| Wind Speed Range | 0 to 60 m/s |
| Power Supply | 10 to 30 VDC |
| Communication Interface | RS-232, RS-485, SDI-12 |
| Protection Class | IP66 |
| Humidity Range | 0 to 100 %RH |
| Wind Direction Range | 0° to 360° |
| Barometric Pressure Range | 600 to 1100 hPa |
| Temperature Range | -40 to +60 °C |
| Operating Temperature | -40 to +60 °C |
| Dimensions | Dependent on configuration |
| Weight | Varies by configuration |
Details document revision history and changes made in each version.
Lists accompanying documentation and software CDs delivered with the system.
Explains symbols and terms used in the manual for warnings and notes.
Lists registered and unregistered trademarks relevant to the product.
Identifies key system components and their names in the product.
Outlines critical safety precautions and warnings for installation and operation.
Provides guidance on protecting electronic circuits from electrostatic discharge.
States the product's compliance with relevant Australian and European Union directives.
Outlines the initial steps and requirements before commencing installation.
Provides guidelines for choosing a suitable site for representative ambient measurements.
Covers the physical placement of the system components.
Details clearance requirements and protection for the mast during installation.
Advises on optimal antenna placement for reliable satellite and GPS communication.
Guides on sensor placement to avoid interference and ensure accurate readings.
Specifies guidelines for installing the main enclosure on a mast.
Covers site preparation, including foundations and utilities.
Emphasizes safety and instructions for laying concrete foundations.
Provides notes for designing concrete foundations specifically for rain gauges.
Details requirements for field cabling and power services.
Instructions on checking and handling unpacked system components.
Lists tools and equipment required for the mechanical installation.
Introduces mast-specific mounting kits and refers to appropriate mast manuals.
Provides guidelines for placing components on a Vaisala Tiltable Pole Mast DKP210.
Details essential procedures for grounding the system and lightning protection.
Specific steps for grounding the enclosure using copper grounding cable.
Explains best practices for mounting wind sensors on top of the mast.
Step-by-step guide for installing the WMT52 wind sensor.
Guidance on selecting the optimal mounting position for reliable WMT52 measurements.
Instructions for securely connecting the WMT52 sensor cable.
Details on how to physically mount the WMT52 sensor onto the mast adapter.
Procedures for correctly aligning the WMT52 sensor using its North arrow marking.
Comprehensive guide for installing the WMT700 wind sensor.
Advice on positioning the WMT700 for optimal wind data collection.
Proper procedures for unpacking and handling the WMT700 sensor.
Detailed steps for connecting the WMT700 sensor cable securely.
Instructions for mounting the WMT700 using a specific fixing kit.
Guidance on mounting two WMT700 sensors on the sensor support arms.
Steps for aligning the WMT700 sensor using a compass.
Pin-out details and wire color information for WMT700 cable 228260.
Guide for installing the WA15 mechanical wind sensor set.
Instructions for connecting the wind transmitter cable within the junction box.
Details on fitting the cable plug and connecting the sensor to the cross arm.
Steps for installing the WA15 wind set on top of a mast.
Procedures for aligning the WA15 wind set using a compass and spirit level.
Guide for installing the WXT520 weather transmitter.
Instructions for connecting the WXT520 sensor cable securely.
Steps for aligning the WXT520 sensor using its North arrow marking.
How to adjust wind direction offset if the sensor cannot be aligned to North.
General guidance on installing the obstruction light relative to other mast components.
Instructions for installing the QOL111 obstruction light using the provided mounting set.
General advice on installing communication devices, including grounding.
Guidance on positioning the UHF antenna for optimal transmission.
Steps for installing the 2G/3G antenna on the mast.
Safety warnings and guidelines related to solar panel installation.
Instructions for mounting the solar panel onto a pole mast using the APPK-SET kit.
Guidance on setting the optimal tilt angle for maximum energy output.
Planning considerations for sensor support arm quantity and placement.
Detailed instructions for installing a full-length support arm on a DKP200 mast.
Detailed instructions for installing a half-length support arm on a DKP200 mast.
Steps for mounting sensor support arms onto a DKE110 mast.
Instructions for attaching sensor support arms to the mast adapter on a DKE200 mast.
Instructions for attaching sensor support arms to the mast adapter on a DKE200 mast.
Guidance on installing the HMP155 humidity and temperature probe.
Steps for mounting HMP155 within the DTR503A radiation shield.
Instructions for mounting HMP155 within the DTR13 radiation shield.
Details on installing HMP155 into a Stevenson Screen.
Instructions for installing the HMP110 humidity and temperature probe.
Guide for installing the SR50A sensor, used as a snow depth sensor.
General instructions for installing CMP pyranometers.
Guide for installing the SP Lite2 pyranometer.
Refers to the Vaisala Visibility Sensor FS11 User's Guide for installation instructions.
Guidance on installing the PWD present weather detector.
Advice on selecting a suitable site for the PWD and avoiding obstacles.
Steps for mounting the PWD sensor onto a sensor support arm.
General safety and placement guidelines for installing the enclosure.
Initial steps before installing the BOX652 enclosure.
Detailed instructions for mounting the BOX652 enclosure onto a pole mast.
Steps for mounting the BOX652 enclosure onto a frangible lattice mast.
Guide for installing the BOX652 enclosure on a wall or back panel using a mounting frame.
Instructions for mounting the BOX652 enclosure directly on a wall or back panel.
Final steps after enclosure installation, including attaching the cabling box cover.
Information on TERMBOX usage and models available for different data lines.
Caution regarding cable length and guidelines for using TERMBOX mounting kits.
Steps for installing the TERMBOX on a pole mast using mounting screws and clamps.
Instructions for attaching the TERMBOX to a frangible lattice mast using a mast adapter.
Emphasizes proper grounding of the TERMBOX with a jacketed cable and rod.
Details on grounding the cable shield through specific cable glands.
General warnings and guidelines for installing subsurface sensors.
Procedures for installing the QMT107 soil temperature sensor.
Guide for installing the QMT110 soil temperature sensor.
Instructions for installing the EC-5 soil moisture sensor.
Steps for installing the EC-5 sensor near the ground surface.
Procedures for installing the EC-5 sensor at a deeper level in the ground.
Guide for installing the DRS511 road and runway sensor.
Lists tools and equipment needed for installing embedded sensors.
Guidelines for using cable ducting to protect sensors and facilitate reinstallation.
Details on cutting slots in the road or runway for DRS511 installation.
Steps for installing DRS511 with cold filling material like epoxy or polyester grout.
Procedures for installing DRS511 using hot filling material such as bitumen.
Information on mounting rain gauge units on separate stands.
Guide for installing the RG13(H) rain gauge, including leveling.
Instructions for mounting the QMR102 rain gauge on its stand.
Steps for installing the OTT Pluvio2 L precipitation gauge on a pedestal.
General warnings and requirements for electrical installation.
Identifies the location of various components within the enclosure.
Steps for preparing the 3G modem, including obtaining and setting a SIM card PIN.
Guide for inserting a CompactFlash memory card into the QML data logger.
Instructions for connecting sensor and device cables to the system.
Lists standard cable lengths included for various sensors and devices.
Guidelines for routing cables along the mast and securing them with cable ties.
Steps for connecting sensor cables using the rubber flange connection.
Procedures for connecting sensor cables using the steel flange connection.
Instructions for connecting Ethernet and other communication cables.
Details on connecting mains cables to the TERMBOX.
Procedures for connecting AC (mains) power and backup battery.
Steps for connecting the AC (mains) power, including external disconnection device.
Guide for mounting and connecting the 12 V / 26 Ah backup battery.
Instructions for connecting solar panel cables to the enclosure.
Sequence for powering up the system after installation is complete.
Instructions on how to repackage sensors for safe transportation.
Details on the QML data logger's connector blocks and channels.
General wiring diagrams for TERMBOX models 1200 and 1212.
Introduces wiring diagrams for the AWS310 system.
Wiring diagram illustrating power connections for the AWS310 system.
Wiring diagram showing data signal connections for the AWS310 system.
Wiring diagram for optional telemetry modules in the AWS310 system.
Wiring diagram for RS line sensors used with the AWS310 system.
Wiring diagram illustrating analog sensor connections for the AWS310 system.
Table correlating analog sensors with telemetry options.
Block diagram illustrating the overall AWS310 system architecture.
Introduces wiring diagrams specific to the AWS310-SITE system.
Wiring diagram for AWS310-SITE power connections.
Wiring diagram for AWS310-SITE data signal connections.
Wiring diagram for optional telemetry in the AWS310-SITE system.
Wiring diagram for RS line sensors used with the AWS310-SITE system.
Wiring diagram for analog sensor connections in the AWS310-SITE system.
Wiring diagram for obstruction light and specific sensors in AWS310-SITE.
Block diagram illustrating the AWS310-SITE system architecture.
To Next Page
