ADVANTEST R3131 - Page 260

R3131 Spectrum Analyzer Operation Manual
Alphabetical Index
I-5
Ref Offset ON/OFF .................................. 3-10
,
3-31
REFERENCE
...................................................... 3-1
Reference level
.................................................. 2-11
Reference Level Display Accuracy
.................. A2-1
Remote control usage examples
........................ 4-50
Remote Enable
..................................................... 4-3
REMOTE lamp
.................................................... 2-8
REMOTE PROGRAMING
................................. 4-1
Removing the window
....................................... 2-27
REN
..................................................................... 4-3
REPEAT
................................................... 3-13
,
3-46
REPEAT (START/STOP)
................................... 2-4
Res 1Hz
....................................................... 3-9
,
3-22
Res 1kHz
..................................................... 3-9
,
3-22
Res 10Hz
..................................................... 3-9
,
3-22
Res 100Hz
................................................... 3-9
,
3-22
Reset File No.
............................................. 3-8
,
3-19
Residual FM
...................................................... A2-2
Residual Response
............................................ A2-2
Resolution bandwidth
.............................. 2-11
,
A2-1
Responses to Interface Messages
......................... 4-3
RETURN
.................................................... 2-2
,
2-15
Revision
...................................................... 3-8
,
3-20
RF attenuator
..................................................... 2-11
RF INPUT 1 connector
........................................ 2-3
RF INPUT 2 connector
........................................ 2-3
RS-232 connector
.............................................. 2-12
RS-232 Remote Control Function
..................... 4-46
[S]
S T U V W X .............................................. 3-9
,
3-24
Sample
...................................................... 3-15
,
3-54
SAVE
................................................ 2-8
,
3-14
,
3-47
Save
........................................................... 3-14
,
3-47
Save Item
.................................................. 3-14
,
3-47
Saving Data
............................................... 2-88
,
3-47
Saving or Recalling Data
................................... 2-88
Screen Annotation
............................................. 2-10
SDC
...................................................................... 4-4
Search ALL/UP/LOW
.............................. 3-11
,
3-35
Selected Device Clear
.......................................... 4-4
Selecting Menu
.................................................. 2-14
Self Test
.................................................... 3-14
,
3-48
Separating Two Signals
..................................... 2-39
Serial Polling Enable
............................................ 4-4
Set Resolution
.................................................... 3-57
Set Up RS232
............................................. 3-8
,
3-20
Setting Date
....................................................... 2-99
Setting GPIB address
........................................... 4-2
Setting Time
....................................................... 2-99
Setting up the measuring window
...................... 2-26
Setting Values .................................................... 3-57
Setup ON/OFF
.......................................... 3-14
,
3-47
SHIFT
......................................................... 2-8
,
3-10
SHIFT, CONFIG(PRESET)
....................... 2-8
,
3-13
SHIFT, COPY(Abort)
................................ 3-7
,
3-21
SHIFT, RECALL(SAVE)
.......................... 2-8
,
3-14
SHIFT, 0(Self Test)
........................................... 3-14
SHIFT, 1(EMC)
................................................. 3-10
SHIFT, 7(CAL)
................................................... 3-7
Sig Track ON/OFF
................................... 3-11
,
3-36
Signal tacking
.................................................... 2-34
SINGLE
............................................ 2-4
,
3-14
,
3-49
Single Sweep
..................................................... 3-49
Slope +/-
................................................... 3-15
,
3-56
Soft key
................................................................ 2-2
Soft-menu
.......................................................... 2-11
Soft-menu display
................................................ 2-2
Sound
.......................... 3-10
,
3-11
,
3-27
,
3-36
,
4-18
Sound AM/FM
...................... 3-10
,
3-11
,
3-27
,
3-36
Sound Off
............................. 3-10
,
3-11
,
3-27
,
3-36
SPAN
................................................ 2-4
,
3-14
,
3-50
SPE
...................................................................... 4-4
SPECIFICATIONS
............................................. 5-1
Specifications for the External Gate Signal
......... 5-4
Specifications for the instrument equipped
with TG option
..................................................... 5-5
Spurious
............................................................ A2-2
Spurious Response
............................................ A2-3
Squelch ON/OFF
.................. 3-10
,
3-11
,
3-27
,
3-36
Standard accessories list
...................................... 1-2
Standard event register
...................................... 4-13
Standard Operation Status Register
................... 4-11
Start
........................................................... 3-10
,
3-28
Start frequency
................................................... 2-11
Status Byte Register
........................................... 4-12
Status bytes
................................................. 4-8
,
4-28
Status Register
..................................................... 4-8
Step keys
.............................................................. 2-5
Stop
........................................................... 3-10
,
3-28
Stop Bit 1/2
................................................. 3-8
,
3-20
Stop frequency
................................................... 2-11
Store A(B) to B(A)
................................... 3-15
,
3-55
Storing
............................................................... 1-12
SWEEP
..................................... 2-7
,
3-15
,
3-51
,
5-2
SWEEP lamp
....................................................... 2-4
Sweep mode
....................................................... 4-16
Sweep time
..................................... 2-11
,
3-51
,
4-16
Switching between the settings
.......................... 2-15
SWP Time
.......................................................... 3-58
SWP Time AUTO/MNL
.......................... 3-15
,
3-51
System checkout
.................................................. 1-8
Aug 28/98