F-2
R3131 Spectrum Analyzer Operation Manual
List of Illustrations
No. Title Page
2-38 Screen Display after Changing the VBW ......................................................................... 2-44
2-39 The Trace after Averaging ................................................................................................ 2-45
2-40 Setup for Input Saturation .................................................................................................2-46
2-41 Screen Display without Saturation ................................................................................... 2-47
2-42 Screen Display Showing Saturation ................................................................................. 2-48
2-43 Setup for Measuring Harmonic Distortion ....................................................................... 2-49
2-44 Screen Display Showing Harmonic Distortion ................................................................. 2-50
2-45 Screen Display Showing Reduced Harmonic Distortion .................................................. 2-51
2-46 Setup for Measuring Intermodulation ............................................................................... 2-52
2-47 Screen Display Showing Intermodulation Distortion ....................................................... 2-53
2-48 Screen Display without Intermodulation Distortion ......................................................... 2-54
2-49 Screen Display Showing the Cal Menu ............................................................................ 2-55
2-50 Editing the Correction Data Table .................................................................................... 2-57
2-51 Screen Display Showing the User-Definable Correction Data Table ............................... 2-58
2-52 Setup for Measuring the Channel Power .......................................................................... 2-59
2-53 Setting the Offset Level .................................................................................................... 2-60
2-54 Setting the Measuring Window ........................................................................................ 2-61
2-55 Measuring the Channel Power .......................................................................................... 2-61
2-56 Setup for Measuring the Occupied Bandwidth ................................................................. 2-62
2-57 Setting the Detector Mode ................................................................................................ 2-63
2-58 OBW Measurement Screen .............................................................................................. 2-64
2-59 OBW(95%) Measurement Screen .................................................................................... 2-64
2-60 Setup for Measuring the Adjacent Channel Leakage Power ............................................ 2-65
2-61 Setting the Specified Bandwidth ....................................................................................... 2-67
2-62 Measurement of the Adjacent Channel Power (ACP POINT) ......................................... 2-67
2-63 Setup for Measuring the Adjacent Channel Leakage Power ............................................ 2-68
2-64 Displaying a Graph as a Result of Operation ................................................................... 2-70
2-65 Adjacent Channel Leakage Power Measurements (ACP GRAPH) .................................. 2-70
2-66 Setup for Measuring the VA Ratio ................................................................................... 2-71
2-67 Performing Max Hold ....................................................................................................... 2-72
2-68 Measuring the Video Carrier Level .................................................................................. 2-73
2-69 Measuring the Audio Carrier Level .................................................................................. 2-73
2-70 Setup for the Pass-Fail judgment ...................................................................................... 2-74
2-71 Pass-Fail Measurement Screen ......................................................................................... 2-75
2-72 Level Window Setting Screen .......................................................................................... 2-76
2-73 Measuring Window Screen ............................................................................................... 2-76
2-74 Setup for Measuring the Harmonic Distortion ................................................................. 2-78
2-75 Measuring the Fundamental Wave ................................................................................... 2-79
2-76 Measuring the Harmonic Distortion ................................................................................. 2-80
2-77 Setup for TG Measurements ............................................................................................. 2-81
2-78 Measurement Screen after a Normalization Calibration ................................................... 2-82
2-79 Connecting the Unit under Test ........................................................................................ 2-83
2-80 Insertion Loss Measurement Screen ................................................................................. 2-84
2-81 3-dB Bandwidth Measurement Screen ............................................................................. 2-84
2-82 Floppy Disk Write Protection ........................................................................................... 2-85
2-83 Screen for the F.Disk Menu .............................................................................................. 2-87
2-84 Screen Display Showing Floppy Disk as the Destination ................................................ 2-88
2-85 Display for Selecting the Data to be Saved ...................................................................... 2-89
Aug 28/98
To Next Page
Loading...
Need help?
General
