Agilent Technologies PNA Series User Manual

Index
Service Guide E8361-90001 Index-5
CPU board
illustrated, 6-13, 6-15
operation
, 5-27
part numbers
, 6-12, 6-14
removal and replacement
illustrated
, 7-29
procedure
, 7-28
troubleshooting
, 4-13, 4-21
cross talk
system test, 3-33
test port test
, 3-33
cross-over cable, LAN , 4-26
CSA mark , 1-6
D
data acquisition
operation, 5-27
data acquisition and processing
subgroup, 5-24
data storage
floppy disk, 5-28
hard disk
, 5-28
IDE
, 5-28
data, option
recovering, B-4
repairing
, B-4
DCOM , A-7
description
functional
digital control group
, 5-5
digital processing group
, 5-5
freqeuency offset group
, 5-4
power supply group
, 5-5
receiver group
, 5-4
signal separation group
, 5-4
synthesized source group
, 5-4
detector
channel R1
illustrated
, 6-21
part number
, 6-20
channel R2
illustrated
, 6-21
part number
, 6-20
detector bracket
illustrated, 6-29
part number
, 6-28
device connections
system verification, 3-24
digital control group
block diagram, 5-25
functional description of
, 5-5
operation
, 5-24
digital processing and control
functional group, 5-3
digital processing group
block diagram, 5-25
functional description of
, 5-5
operation
, 5-24
directivity
cause of failure, A-10
definition of
, A-10
measurements affected by
, A-10
display assembly
illustrated, 6-11
operation
, 5-26
parts list
, 6-10
removal and replacement
illustrated
, 7-13
procedure
, 7-12
troubleshooting
, 4-13, 4-17
display inverter
removal and replacement
illustrated
, 7-15
procedure
, 7-14
display lamp
removal and replacement
illustrated
, 7-15
procedure
, 7-14
Display port
rear panel connector, 5-28
display test
running, 4-19
documentation
optional, 1-iv
part numbers
, 6-38
standard
, 1-iv
dynamic range, high
configuration
, 5-19
E
earth ground , 1-3
electrostatic discharge, See ESD
emissions requirements
German FTZ, 1-7
environment, operating
specifications, 3-4
verification
, 3-4
equipment rack
horizontal spacing, 2-5
mounting analyzer in
, 2-5
equipment, service test
required, 2-6
error terms
access to, A-6
via COM/DCOM commands
,
A-7
via front panel
, A-6
via SCPI commands (using
GPIB)
, A-7
cause of failure to
, A-3
descriptions
, A-8
directivity
, A-10
flowgraph of one port
, A-4
flowgraph of two port
, A-5
identifying using flowgraphs
,
A-4
isolation
, A-15
load match
, A-12
magnitude
affected by
, A-3
monitoring over time
, A-3
reflection tracking
, A-13
shape affected by
, A-3
source match
, A-11
transmission tracking
, A-14
typical data
, A-8
using as diagnostic tool
, A-3
using to aid troubleshooting
,
A-3
worse than typical values
, A-8
ESD
protection, 1-5, 3-4, 4-3, 7-3,
A-4
supplies
part numbers
, 6-39
exchange
module
procedure
, 6-5
rebuilt assemblies
program
, 6-5
EXT 10 MHz REF IN connector
rear panel, 5-10
EXT 10 MHz REF OUT connector
rear panel, 5-10
extender board
measurement points, 4-8
voltages
, 4-8
external analyzer
replaceable parts
illustrated
, 6-35
part numbers
, 6-34
external monitor , 4-13
F
failure
band related, 4-32
broadband
, 4-32, 4-41
of connector repeatability check
,
3-18
of insertion loss check
, 3-14
of magnitude and phase
stability check
, 3-16
of operator’s check
, 3-11
of return loss check
, 3-13
of system verification
, 3-25
flowchart
, 3-25
single band
, 4-32
single vs. broadband
, 4-41
fan
removal and replacement, 7-62
troubleshooting
, 4-12

Agilent Technologies PNA Series Specifications

General

Brand	Agilent Technologies
Model	PNA Series
Category	Measuring Instruments
Language	English