Index
Service Guide E8361-90001 Index-15
measurement system, 4-28
frequency offset (080) group
,
4-54
frequency offset group (option
080)
, 4-54
receiver group
, 4-52
running the receiver display
,
4-30
signal separation group
, 4-49
source group
, 4-35, 4-41
traces A, B, R1, R2
, 4-30
where to begin
, 4-31
order of removal of boards
, 4-10
PARALLEL port
, 4-22
ping command
, 4-24
power output of channel A
, 4-49
power output of channel B
, 4-49
power up
, 4-6
power supply check
, 4-7
probe power
, 4-17
rear panel
, 4-21
rear-panel USB
, 4-21
receiver output
, 4-53
receiver output (A13)
, 4-57
RPG
, 4-17
RS-232 port
, 4-22
SERIAL port
, 4-22
source 20
, 4-41
source group
single vs. broadband
, 4-41
speaker
, 4-17
trace A
, 4-30
trace B
, 4-30
trace R1
, 4-30
trace R2
, 4-30
typical power output
Port 1
, 4-49
Port 2
, 4-50
using controllers to system
troubleshoot
, 4-23
using error terms
, A-3
using the extender board
, 4-8
VGA port
, 4-22
where to begin
, 4-4
U
uncertainty
measurement, 3-20
uninstalling options
, B-3
upgrade
configurable test set,
Option 014
, 2-3
time domain, Option 010
, 2-3
upgrade kits
part numbers, 6-39
upgrade, firmware
downloading from the internet,
C-2
installing using Option 099
, C-3
Option 099
, 2-4
upgrade, frequency offset mode
Option 016, 2-4
upgrade, transfer switch
Option 081, 2-4
USB
accessories
CD-RW drive
, 2-4
hub
, 2-4
part numbers
, 6-39
front panel
troubleshooting
, 4-17
port
front panel connector
, 5-26
rear panel connector
, 5-28
rear panel
troubleshooting
, 4-21
USB hub
operation, 5-28
removal and replacement
, 7-65
illustrated
, 7-65
utility
option enable
accessing
, B-3
dialog box
, B-3
V
VCO (voltage-controlled
oscillator)
defined, 5-6
verification
ANSI/NCSL Z540-1-1994, 3-8
kits
, 2-7, 3-7
substitution
, 3-22
non-ANSI/NCSL Z540-1-1994
,
3-9
of operating environment
, 3-4
of operating specifications
, 3-4
system
, 3-1, 3-7, 3-19, B-1, C-1
device connections
, 3-24
dialog box
, 3-23
example of results
, 3-26, 3-27
failure flowchart
, 3-25
failure of
, 3-25
getting ready
, 3-4
interpreting results
, 3-26
performing
, 3-22
procedure
, 3-23
test setup
, 3-23
what it verifies
, 3-19
VGA monitor
, 4-13
VGA port
rear panel connector, 5-28
troubleshooting
, 4-22
W
warm up
analyzer, 3-4
warning
, 1-3
warnings for servicing
, 1-4
warranty
service
standard
, 2-10
three-year return to Agilent
,
2-10
Windows
, 2-6
Y
YIG (yttrium-iron-garnet)
defined, 5-6
YIG oscillator
PMYO frequency adjustment,
3-51
YTO (YIG-tuned oscillator)
defined, 5-10
theory of operation
, 5-10
To Previous Page
Loading...
Need help?
General
