Allen-Bradley SLC 500 - Page 242

Index
I–9
Publication 1747-6.2
sinking and sourcing, 7-1
contact output circuits, 7-2
Sinking Device with Sourcing Input
Module Circuit, 7-3
Sinking Device with Sourcing Output
Module Circuit, 7-3
solid-state DC I/O circuits, 7-2
Sourcing Device with Sinking Input
Module, 7-2
Sourcing Device with Sinking Output
Module Circuit, 7-3
slave devices, DF1 half-duplex protocol, B-5
SLC 5/03 and SLC 5/04 processors, initial
factory conditions, channel 0
configuration, 1-6
SLC 5/03 processor , channel 0, RS-232
communication, B-2
SLC 5/04 processors
channel 0, RS-232 communication, B-2
initial factory conditions, channel 1
configuration, 1-6
SLC 5/05, Ethernet communications, G-1
SLC 5/05 processors
channel 0, RS-232 communication, B-2
initial factory conditions
channel 0 configuration, 1-6
channel 1 configuration, 1-6
SLC 500 BASIC Module Design and
Integration Manual, B-3
SLC 500 Family of Small Programmable
Controllers, system overview , 2-1,
2-10, 2-1
1
SLC 500 Programmable Controllers
general specifications, 2-9
installing, 6-1
selecting a memory module, 2-18, 2-20
selecting a processor
, 2-4
Selecting Discrete I/O Modules, 2-10
Selecting Enclosures, 2-15
Selecting Isloation T
ransformers, 2-22
Selecting Operator Interfaces, 2-15
Selecting Power Supplies, 2-1
1
Selecting Speciality I/O Modules, 2-10
Special Considerations, 2-23
troubleshooting, 10-1
Spacing Y our Controllers, 3-2
specialty I/O modules, 2-10
specifications
power supplies
24V dc user power output current,
2-11
24V dc user power output voltage,
2-11
ambient operating temperature rating,
2-11
certification, 2-1 1
fuse protection, 2-1 1
humidity rating, 2-1 1
internal current capacity , 2-1 1
line voltage, 2-1 1
maximum inrush current, 2-1 1
storage temperature, 2-1 1
typical line power requirement, 2-1 1
wiring, 2-1 1
processor , maximum chassis/slots, 2-9
processors
ambient temperature rating, 2-9
certification, 2-9
clock/calendar accuracy , 2-9
humidity , 2-9
LED indicators, 2-9
local I/O capacity , 2-9
memory back-up options, 2-9
noise immunity , 2-9
power supply loading at 5V dc, 2-9
program memory , 2-9
program scan hold-up time after loss of
power , 2-9
remote I/O capacity , 2-9
scan time, typical, 2-9
shock (operating), 2-9
standard RAM, 2-9
vibration, 2-9
Starting Up Your Control System, 8-1
conduct a dry run, 8-12
disconnect motion-causing devices, 8-2
enter and test your program, 8-9
initialize and test your processors, 8-3
inspect your installation, 8-2
observe control motion, 8-1
1
test your inputs, 8-5
test your outputs, 8-7
start-up instructions, 1-1
storage temperature, power supply
specification, 2-1
1
surge suppression circuits, 2-26
surge suppressors
for contactor , 2-25
for motor starters, 2-25
for relays, 2-25
system configuration, example, A-5