Analog way VIO 4K - Multi-Outputs Support; Programmers Gu; Extra Screen

To Next Page

To Previous Page

233

www.analogway.com

PROGRAMMER’S GUIDE

USER MANUAL

Each time a video expansion card is installed, a new output is available. The Area of Interest (AOI) and the

rotation of each output are totally independent from those set for the other outputs.

Each time a video expansion card is installed, a new screen is available. If two video cards are installed then

three screens and three output resources are available.

15.3 Multi-Outputs support

15.3.1 Extra screen

Main Page

Default Chapter3
- Default Chapter3
  - Table of Contents3
- 1 Introduction7
- 2 Safety Instructions11
- 3 Physical Description17
- 4 Quick Setup & Operation19
Programmer's Gu19
Programmer's Gu20
- Web RCS Interface23
- Connecting to the Web RCS (LAN)23
- Connecting to the Web RCS (USB)25
Programmer's Gu25
- Operating from the Web RCS Interface29
- 5 Device Management31
  - Powering-Up31
Programmer's Gu31
- Sending the Device to Standby31
- Adjusting the Front Panel32
- Setting up the LAN Connection37
- Enabling the USB Device Connection39
- Using the GPO Connection42
- Resetting the Unit44
- Creating Backups47
- Erasing the Device Memories53
- Updating the Device58
- 6 Output Management60
Programmer's Gu64
- Setting up the Plug66
- Setting up the Format74
- Setting up the Output64
  - Checking the Plug Status64
Programmer's Gu74
- Adjusting the AOI (Area of Interest)81
- Rotating the Output84
- Correcting the Image85
Programmer's Gu85
- Using Test Patterns87
- Monitoring the Output90
Programmer's Gu90
- Freezing the Output91
- Capturing the Output92
  - Using the Genlock Reference92
Programmer's Gu92
- Enabling Loop Mode94
- 7 Input Management96
Programmer's Gu96
- Supported Inputs (Formats and Signals)96
- What Is an Input96
- Checking Your Inputs Status98
- Auto-Setting All Inputs100
- Setting up an Input101
- Monitoring Input Sources147
- Capturing the Input149
- Looping-Through Inputs149
- 8 Frame Management150
- 9 Screen Management163
  - Adjusting the View163
Programmer's Gu163
- What Is a Screen163
- Customizing the Transition Effect166
- Controlling the Screen168
Programmer's Gu168
- 10 Audio Management172
- Audio Inputs and Outputs172
Programmer's Gu172
- Supported Audio172
- A/V Mapping Inputs and Outputs173
Programmer's Gu178
- Selecting the Sampling Rate178
- Adjusting the Input Audio179
- Adjusting the Output Audio189
- Adjusting the XLR Audio201
Programmer's Gu201
- Prelistening to Audio Content205
- 1 Custom Formats207
  - Creating Custom Formats207
Programmer's Gu207
- What Are Custom Formats207
- Using Custom Formats211
- 2 Presets212
  - Creating Presets212
- 3 EDID Support216
- 4 HDCP Support225
- 5 Expansion Interfaces230
  - Audio Expansion Interfaces230
    - Dante™ Audio Expansion Interface230
    - XLR Audio Expansion Interface230
Programmer's Gu231
- 60P Expansion Interface231
- 60P + SDI Expansion Interface232
- Video Cards231
  - Extra Output Expansion Interface231
- Multi-Outputs Support233
Programmer's Gu233
- Extra Screen233
- Pitch Compensation234
Programmer's Gu234
- Contact Information236

Analog way VIO 4K - Multi-Outputs Support; Programmers Gu; Extra Screen

Table of Contents

Other manuals for Analog way VIO 4K

Related product manuals