Chapter 8
8-38
Ink tank error.
Press OK and replace ink
tank.
03830206-2547 MBK2 ink tank ID error Replace with a valid MBK ink tank.
Ink tank error.
Press OK and replace ink
tank.
03830207-254A R ink tank ID error Replace with a valid R ink tank.
Ink tank error.
Press OK and replace ink
tank.
03830208-254C G ink tank ID error Replace with a valid G ink tank.
Ink tank error.
Press OK and replace ink
tank.
03830209-254B B ink tank ID error Replace with a valid B ink tank.
Ink tank error.
Press OK and replace ink
tank.
03830212-2544 PM ink tank ID error Replace with a valid PM ink tank.
Ink tank error.
Press OK and replace ink
tank.
03830213-2545 PC ink tank ID error Replace with a valid PC ink tank.
Ink tank error.
Press OK and replace ink
tank.
03830215-2549 PGY ink tank ID error Replace with a valid PGY ink tank.
Maintenance cartridge full.
Replace the maintenance
cartridge.
03841001-2819 Maintenance cartridge full Renew the maintenance cartridge.
No Maintenance Cartridge
capacity.
Replace the maintenance
cartridge.
03841001-281B Not enough space in the maintenance cartridge prior
to cleaning
Replace the maintenance cartridge.
No maintenance cartridge.
Check the maintenance
cartridge.
03841101-2818 Mauntenance cartridge not installed Install the maintenance cartridge.
Maintenance cartridge
problem.
Replace the maintenance
cartridge.
03841201-2816 Maintenance cartridge EEPROM error Renew the maintenance cartridge.
Maintenance cartridge
problem.
Replace the maintenance
cartridge.
03841201-2817 Maintenance cartridge ID error Renew the maintenance cartridge.
Manual printing is selected,
but a roll is loaded.
Press Load/Eject and
remove the roll.
03860001-2E0C Data with a cut sheet specification has been received
when roll media are loaded.
Load cut sheets at the paper tray port.
Sheet printing is selected.
Press Load/Eject and load
sheets.
03860002-2E02 Data with a cut sheet specification has been received
but no cut sheets are loaded.
Load cut sheets at the paper tray port.
Roll printing is selected, but
sheets are loaded.
Press OK, remove the
sheets, and load a roll.
03860002-2E0A Data with a roll media specification has been received
when a cut sheet tray is loaded.
Replace with roll media.
This type of media is not
compatible with HP-GL/2.
03860006-2825 Paper type mismatch at HP-GL/2 printing Exchange for the compatible paper to HP-GL/2
before reprinting.
Borderless printng not
possible. Check roll
position.
Online: Print
Load/Eject: Change Paper
03861001-2405 Paper loaded at a position inaccessible for borderless
printing
Check to see if a borderless printing spacer is
installed.
Reload the paper.
Borderless printng not
possible.
Check paper size setting.
03861001-2406 Data unfit for borderless printing Check the data, and then print again.
Borderless printng not
possible.
Paper stretched or shrank.
Confirm usage cond. of the
paper.
03861001-2407 Borderless printing disabled (engine detection) Reload the paper.
Borderless printng not
possible.
Check supported paper.
03861001-2408 Borderless printing disabled (unsupported size) Check the media size.
Change the media size.
Insufficient paper for job.
Online: Print
Stop: Stop Printing
Load/Eject: Change Paper
03862000-2E09 Not enough roll media on remaining roll media
quantity detection
Renew the supply of roll media.
Insufficient paper for job. 03862001-2E31 Not enough roll media Renew the supply of roll media.
Insufficient paper for job. 03862002-2E32 Not enough roll media (lower roll) Renew the supply of roll media.
Cannot adjust printhead.
Press Online to clear the
error and readjust printhead.
03863000-2820 Printhead registration unadjustable Check the paper on which a pattern is printed for
smears.
Check the environment for interferences from
outside light.
Clean the printhead.
Display massage Code* Condition detected Action
To Next Page
Loading...
